Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
The 3 multi-display lights : Top light can indicate: : Middle light – the current stage of the wash programme selected. : Bottom light – which fault has occurred on the dishwasher. Control indicators have the following meaning: Refill with special salt J Refill with rinse aid H 3 The control indicators never light up while a wash programme is running. Operating Instructions Prior to using for the first time Prior to using for the first time, remove all the clips with which the baskets are secured for transport. Then perform the following steps: 0 1. Adjust the water softener 2. Fill with Salt for the Water Softener 3. Fill with Rinse Aid Adjust the water softener To prevent the build up of limescale on dishes and in the dishwasher, the dishes must be washed with soft water, i.e. water with a low lime content. For this reason the dishwasher is fitted with a water softener in which tap water from a hardness of 4 °d (German degree) is softened with the aid of special salt. 3 Your local water authority can advise you on the hardness of the water in your area. The water softener can be set manually using the water hardness switch; it can also be set electronically using the buttons on the control panel. Water hardness Hardness setting Number of in °d1) in mmol/l2) Range manual electronic flashes 41 - 50 7.3 – 9.0 IV 5 5 1 30 - 40 5.3 – 7.2 IV 4 4 19 - 29 3.3 – 5.2 III/IV 3* 3 4 - 18 0.7 – 3.2 I/II/III 2 2 0* 1 under 4 under 0.7 I no salt 1 required 1)(°d) German degrees, a measure of water hardness 2)(ppm), parts per million *factory setting Operating Instructions Adjust the water softener to the water hardness setting for your area as shown in the table. 1 It is only possible to adjust the water hardness setting when no programme is running. If you have accidentally started a programme (a LED stays on permanently), the pr ing the appropriate button. 0 1. The dishwasher must be switched off. 2. Manual setting: Open the door on the dishwashe 3. Remove the lower basket dishwasher. 4. Turn the water hardness switch to0or 1. 5. Re-position the lower basket. 6. Electronic setting: Press the softener and function buttons simultaneously and keep them pressed. 7. In addition press the ON/OFF button. 8. The LED indicators for the water softener and function buttons flash. 9. Press the softener button again. – At first the LED indicator for the water softener button will light up continuously for 5 seconds and then begin to flash. – The number of flashes corresponds to the hardness setting. – The sequence of flashes is repeated several times after a 5 second pause. 10. Each time you press the water-softener button the hardness setting will go up by 1. (Exception: Hardness setting 1 follows hardness setting 5). – If the hardness setting is changed, the LED indicator for the water- softener button will confirm the change by remaining illuminated continuously for 5 seconds and then flashing again. – The number of flashes corresponds to the new hardness setting. – The sequence of flashes is repeated several times after a 5 second pause. 11. Once the hardness setting is correctly adjusted, press the ON/OFF button. The hardness setting is then stored. 11 Operating Instructions Filling with Salt for the Water Softener 1 Use only salt designed for dishwashers. Never fill the salt container with any another type of salt (e.g. culinary salt) or dishwasher detergent as this would irreparably damage the water softener. Prior to filling with salt, please check each time that you really do have a packet of dishwasher salt in your hand. Fill with dishwasher salt: – Prior to using the dishwasher for the first time – When the SALT indicator J on the control panel is illuminated. 3 If the water hardness in your area is less than 4 °d, you do not need to use dishwasher salt. The SALT indicator J3 The water expelled by filling the salt container with salt runs o salt container onto the base of the washing compartment. This is cause for concern, the water will be pumped out at the start of the SALESALTSALZSEL remain illuminated. 0 1. Open the door, remove the lower basket. 2. Undo the lid on the salt container by turning it anticlockwise. 3. When using for the first time: fill the salt container with water. 4. Place the funnel supplied on the container opening. Fill the container with salt through the funnel; the capacity of the co tainer is approx. 1.0-1.5 kg depending on the grain size. Do not overfill the salt container with salt. next wash programme. 5. Clean any salt remnants on the container opening. 6. Turn the lid clockwise to the stop, otherwise dishwasher salt will leak into the wash water, this could lead to poor wash results. To avoid this run a rinse programme after filling the salt container with special salt. This will wash away salt water and any salt crystals that have been spilt. 3 Depending on the size of the salt grains, it can take several hours for the salt to dissolve in the water and the special salt indicator J to ext...