Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Each time you press the button, the counter "L" will display the number of hours the cycle start has been delayed by in sequence; choose the time you prefer. The delayed start indicator light "H" flashes and when the appliance starts, the counter will begin the countdown to the delayed start. When this time is up, the wash cycle will begin and the counter will now serve to display the amount of time left until the end of the wash cycle. NOTE: • it is best if you keep from modifying anything during countdown; if this is absolutely necessary, then turn the knob to the RESET position: 4 beeps and the 3 dashes appearing indicate that all settings have been cancelled Repeat the operations for "dishwasher delayed start programming" and for "starting and setting the wash cycle" following the instructions in the relative paragraphs. • Should there be a power failure or should the door of the appliance be opened during the countdown, the latter will come to a stop and will re-start either when the power comes back on or when the door is closed. Wash cycle modification buttons Half load selection button on upper or lower rack. This can be selected before setting any wash cycle, yet we remind you that you should halve the amount of detergent recommended for the wash cycle you have selected (see wash cycle table). Press button "I" and you will hear a beep, the indicator "N" appears on the display: you can select which rack to perform the half load on. Each time the button is pressed, you will hear a beep, and symbol appears indicating the wash on the upper rack, whereas symbol indicates the wash on the lower rack. Press the button again and you will hear another beep, thereby resetting the selection and the appliance will consequently wash on both racks. To use the racks correctly, we recommend you read the chapter entitled "Loading the dishes". GB 8 Wash Cycle Table Cycle Cycle selection instructions Cycle description Detergent for pre-wash + wash Rinse Aid 1) Intensiv Very dirty dishes and pans (not to be used for delicate items). Pre-wash with cold water Pre-wash with hot water at 45°C. Extended wash at 70°C. 1 rinse with cold water. Hot rinse at 70°C. Drying. 8+22 g. * 2) Normal (IEC-EN 50242) Normally dirty pans and dishes. Standard daily cycle. 2 pre-washes with cold water. Extended wash at 55°C. Hot rinse at 70°C. Drying. 8+22 g. * 3) After Dinner Normally dirty pans and dishes with no dry residue. 2 Pre-washes with cold water. Wash at 55°C. Hot rinse at 70°C. Drying. 8+22 g. * 4) Delicates Economic and fast cycle to be used for more delicate items which are sensitive to high temperatures. Run cycle immediately after use. Wash at 50°C. Lukewarm rinse. Hot rinse at 70°C. Drying. 22 g. * 5) Rapid 25’ Economic and fast cycle to be used for slightly dirty dishes. Run cycle immediately after use. No drying. Short wash at 45°C. Cold rinse. 22 g. 6) Hot Rinse To be used for dishes that only need to be rinsed. Hot rinse at 70°C. Drying. * 7) Soak Preliminary wash cycle for dishes and pans awaiting completion of the load with the dishes from the next meal. Short cold wash to prevent food from drying onto the dishes. 9 GB Energy Saving Tips -It is important to try and run the dishwasher when it is fully loaded in order to save on energy. In order to prevent odors from forming and food from caking onto the dishes, you can run the hold cycle. -Choose the right wash cycle: the choice of cycle depends on the type of dishware, cookware and utensils being washed and how dirty they are. -Use the right amount of detergent: if you use too much detergent, the result will not be cleaner dishes, but, rather, a greater negative impact on the environment. -There is no utility in rinsing dishes, cookware and utensils before placing them in the dishwasher. How to Keep Your Dishwasher in Shape After Every Wash After every wash, turn off the water supply to the appliance and leave the door slightly ajar so that moisture and odors are not trapped inside. Remove the Plug Before cleaning or performing maintenance, always remove the plug from the socket. Do not run risks. No Solvents or Abrasive Cleaning Products To clean the exterior and rubber parts of the dishwasher, do not use solvents or abrasive cleaning products. Rather, use only a cloth and warm soapy water. To remove spots or stains from the surface of the interior, use a cloth dampened with water and a little white vinegar, or a cleaning product made specifically for dishwashers. When You Go on Holiday When you go on holiday, it is recommended that you run a wash cycle with the dishwasher empty and then remove the plug from the socket, turn off the water supply and leave the door of the appliance slightly ajar. This will help the seals last longer and prevent odors from forming within the appliance. Moving the Appliance If the appliance must be moved, try to keep it in the vertical position. If absolutely necessary, it can be positioned on its back. Seals One of the factors that caus...