Оценок - 5, средний балл: 4.6
(
)
)
|
Фрагмент инструкции
If the saucepans and frying pans are very dirty, allow them to soak before being washed. You will thus avoid having to wash them again. To make it easier to load your dishes, pull the racks out fully. How to use the lower rack We recommend you place the most difficult dishes to wash into the lower rack: saucepans, lids, soup dishes and plates (load examples are shown in the photo). • Serving dishes and large lids: place them on the sides of the rack. • Saucepans, salad bowls: must always be placed upside down. • Very deep dishes: place them obliquely, thus allowing water to run down them and cleaning them better. The cutlery basket (Figures A,B) The cutlery basket can be split up by pulling out the handle and removing the clip that keeps the two parts joined together (see figures A and B). When you only have little cutlery to wash, you can use just half the basket. This basket is equipped with two removable grids: insert the cutlery one by one into the slots, with the handles at the fig. A bottom. Position them so that they don't touch. How to use the upper rack Place delicate and lightweight dishes in the upper rack: glasses, tea cups and coffee cups, saucers - but plates too -shallow salad bowls, slightly dirty frying pans and shallow pans (the photo illustrates a few examples). Position lightweight dishes in such as way as to avoid their being moved by the spray of water. The upper rack can be equipped with one or two special tip-up compartments for mugs and cups, as well as spoons, knives and forks, which should be fitted in the slots provided. Stemmed glasses can be hooked onto these compartments by threading the stems into the slots provided (see fig. D). After loading the dishes, remember to check that the blades on the sprayer arms can turn freely without knocking against any dishes. How to adjust the upper rack …. The upper rack can be set in a high or low position. There are two handles on the sides of the upper rack: use these to adjust its height (see figure C). Load examples upper rack lower rack fig. C fig. B fig. D fig. A 5 GB Turning on the Appliance First of all Insert the plug into the electricity socket to power the dishwasher. Turn on the water tap completely and press ONOFF button "A"; the display lights up and the wash cycle time selected on the knob will flash. Selecting and starting a wash cycle. • Select the desired wash cycle by turning knob "D" clockwise from wash cycle 1 to 7 and anticlockwise from 7 to 1; the display indicates the average duration of the wash cycle and the cycle phases it consists of (consult the wash cycle table contained on page 7, especially when first using the appliance). • Press the Start button "R" and the wash cycle starts up, emitting a double beep; the approximate amount of time left until the end of the wash cycle is displayed. • If the time indicated at the start of the wash cycle does not correspond to the actual duration of the cycle itself, this could be for a number of reasons: the temperature of the inlet water, the degree of soil, prolonged attempts by the appliance to clean the wash filter from food residue clogging it, etc. Cycle phase under way indicator While the wash cycle is under way, the symbols corresponding to the cycle phases light up in sequence. Here are the symbols corresponding to each cycle phase: Pre-wash Wash Rinses Drying Cancelling and modifying a wash cycle in progress Premise: a wash cycle in progress can only be modified if it hasn't been running for long. Keep the Reset button "R" pressed for about 3 seconds: a prolonged beep will sound, followed by three short beeps. The cancelled cycle time will flash on the display. Turn the knob to select a new wash cycle. You've left out a dish? You can interrupt a wash cycle by pressing the "ON-OFF" button, then place the forgotten dishes into the appliance, which will start up, after approximately 10 seconds, from where it was interrupted when you turn it back on. There's been a power failure? Has the dishwasher door been opened? The wash cycle stops and 3 dashes appear on the display; the cycle restarts as soon as the electricity comes back on or when the door is shut. At the end of the wash cycle The end of the wash cycle is indicated by two short beeps and the word "END" flashes on the display. • Turn the appliance off at the ON-OFF button • Turn off the water tap. • Empty the lower rack first. Make sure the wash cycle has ended before removing the dishes! Warning: when you open the dishwasher door after the wash cycle has just ended or is under way, take care not to scald yourself with the hot steam. How to set the extra drying Press button "E". After a prolonged beep, indicator light "G" lights up and the time corresponding to the wash cycle selected on the knob will flash on the display. Note: The time indicated on the display is extended due to the extra drying time. To disable the extra drying option, press the same button and indicator light "G" will be turned off after a...
Эта инструкция также подходит к моделям:Посудомоечные машины - IDE1000UK (356.59 kb)