Оценок - , средний балл:
(
)
)
Производитель: Frigidaire
Размер: 290.83 kb
Название файла: 154768201b.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
Motor (Amps) ........................................... 1.8 Heater Wattage ....................................... 900 Total Amps (load rated) ......................... 10.0 TempAssure .............................. 140°F ±5°F (60°C±3°C) [with outer door in place] TempBoost............. 145°F ±5°F (63°C ±3°C) Heated Wash/Heated Rinse Sanitize .................. 150°F ±5°F (66°C ±3°C) Hi-Limit Thermostat ................ 200°F (93°C) Water Supply Suggested minimum incoming water temperature ............................. 120°F (49°C) Pressure (PSI) min./max. ................... 20/120 Connection (NPT) ..................................... 3/8" Consumption (Normal Cycle) ....................... ............. 4.9 - 9.7 U.S. gal., 18.5 - 36.7 liters Water valve flow rate (U.S. GPM) ........... .83 Water recirculation rate (U.S. GPM) .............. .................................................... approx. 12 Water fill time ..................................... 87 sec. To replace dispenser: • shut off electricity to dishwasher, • remove outer door panel assembly, • disconnect wiring to the actuator, • remove the six screws, • remove the dispenser, • replace and reinstall screws, • rewire actuator. Check the Following 1. Fuse (blown or tripped). 2. 120 VAC supply wiring connection faulty. 3. Electronic control board defective. 4. No 12 VAC power to control. 5. Motor (inoperative). 6. Door switch (open contacts). 7. Door latch not making contact with door switch. 8. Touch pad circuit defective. 9. No indicator lamps illuminate when START or OPTIONS are pressed. 1. Motor (bad bearings). 2. Motor stuck due to prolonged non-use. 1. Improper voltage. 2. Motor windings shorted. 3. Glass or foreign items in pump. 1. Heater element (open). 2. Electronic control board defective. 3. Wiring or terminal defective. 4. Hi-Limit thermostat defective. 1. Latch mechanism defective. 2. Electronic control board defective. 3. Wiring or terminal defective. 4. Broken spring(s). 5. Defective actuator. 1. Drain restricted. 2. Electronic control board defective. 3. Defective drain pump. 4. Blocked impeller. 5. Open windings. 6. Wiring or terminal defective. 1. Water supply turned off. 2. Defective water inlet fill valve. 3. Check fill valve screen for obstructions. 4. Defective float switch. 5. Electronic control board defective. 6. Wiring or terminal defective. 7. Float stuck in “UP” position. 1. Drain hose (high) loop too low. 2. Drain line connected to a floor drain not vented. 1. Detergent allowed to stand too long in dispenser. 2. Dispenser wet when detergent was added. 3. Detergent cover held closed or blocked by large dishes. 4. Improper incoming water temperature to properly dissolve detergent. 5. See "Detergent cover will not open." Always disconnect the dishwasher from the electrical power source before adjusting or replacing components. Personal Injury Hazard is attached by a worm gear clamp to the discharge end of the drain pump. The drain hose must have a loop at a minimum height of 32 inches in order to insure proper drainage. The main pump can easily be removed by disconnecting the upper spray arm supply tube hose, the drain pump connector hose, the wiring harness connections made at the circulation motor, the water heat thermistor located on the bottom of the pump and rotating the four sump retainers toward the middle of the sump. Pump Assembly The pump assembly is driven by a synchronous motor. Rotation is in the counterclockwise direction at 3600 RPM. The motor drives a pump which supplies 100 percent filtered water at a rate of approximately 12 GPM to one spray arm at a time. The spray arm’s operation is alternated by small “pauses” of the motor during the wash cycle. Draining is accomplished by using a small separate synchronous drain pump mounted to the side of the sump. The drain pump is connected to the main pump by a small rubber hose. The drain check valve is located at the discharge end of the drain pump. The drain hose Short Turn Gasket Cross Section Detergent and Rinse Aid Dispenser The detergent and rinse aid dispenser is a one piece component consisting of a molded detergent cup and a built-in rinse aid dispenser. The detergent cup has a spring loaded cover and the rinse aid dispenser has a removable cover. Liquid rinse aid is added to the dispenser up to the fill line indicator. The amount of rinse aid released can be adjusted by turning the arrow indicator from one, being the least amount, to four, being the greatest amount. Mounting Rib Tub Interior Remedy 1. Replace fuse or reset breaker. 2. Repair or replace wire fasteners at dishwasher junction box. 3. Replace control board. 4. Replace control board. 5. Replace motor/impeller assembly. 6. Replace latch assembly. 7. Replace latch assembly. 8. Replace console assembly. 9. Replace console assembly. 1. Replace motor assembly. 2. Rotate motor impeller. 1. Check voltage. 2. Replace motor/impeller assembly. 3. Clean and clear blockage. 1. Replace heater el...