Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Itshould be at least 120°F (49°C). (SeeFactors Affecting Performance.) • Check water hardness. For extremely hardwater, it may be necessary to install a watersoftener. (See Detergent Chart.) • Use fresh detergent. • Check to make sure funnel in top rack is not blocked. • Make sure items are not blocking the spray arms, preventing them from rotating. Dishes not Dry • Select heat dry option. • Make sure the rinse aid dispenser is filled. • Increase the amount of rinse aid. (See RinseAid.) • Check the incoming water temperature. Besure it is at least 120°F (49°C). • Check for proper loading—avoid nestingitems. • Plastic items may need to be towel dried. • Cups with a concave bottom will collect water. Glassware/Flatware Spotted or Cloudy • Check water hardness. For extremely hard water, it may be necessary to install a watersoftener. (See Detergent Chart.) • Water temperature may be low. Avoidextremely low or high temperatures. (SeeFactors Affecting Performance.) • Avoid overloading and improper loading. (See Preparing and Loading Dishes.) • Use fresh detergent. Old detergent isineffective. • Make sure rinse aid dispenser is filled. • Check to see that proper amount ofdetergent is being used for cycle selected. Also, check phosphate level. (See DetergentDispenser.) • Home water pressure may be too low—it should be 20 to 120 pounds per square inch(psi). Dishware Chipped • Load with care and do not overload. (SeePreparing and Loading Dishes.) • Place delicate items in top rack. • Place glasses securely against pins and notover pins. • Load items so they are secure and don’t jarloose when moving racks in and out. Moveracks in and out slowly. • Make sure tall glasses and stemware willclear top of tub when rack is pushed in. • Fine antique china and crystal should behand-washed. 15 Solutions to Common Dishwashing Problems (continued) Dishware Stained or Discolored Dishwasher Leaks • Tea and coffee can stain cups. Remove the stains by hand washing in a solution of 1/2cup (120 ml) bleach and one quart (1 L) ofwarm water. Rinse thoroughly. • Iron deposits in water can cause a yellow orbrown film. A special filter installed in the water supply line will correct this problem. (See Removing Spots and Film.) • Aluminum utensils can leave gray/black marks when they rub against other items. Load properly. • Certain high acid foods can causediscoloration of stainless steel and plasticsif allowed to sit for a long period. Use the Rinse & Hold cycle or rinse by hand if notoperating dishwasher at once. • Mixing stainless steel and silver utensils in silverware basket can cause pitting of thestainless steel blades. Avoid mixingstainless steel and silver. Etching • Using too much detergent in soft or softenedwater causes this film that cannot be removed. • Adjust the amount of detergent based on thewater hardness. (Check Detergent Chart.) • Lower the water temperature. • Use no heat dry option. Detergent Left in Cups • Detergent may be old. Discard and usefresh detergent. • Be sure water action can reach the dispenser. • Check to see if cycle has been completed. • Make sure items do not prevent the detergent dispenser from opening. • Use only fresh detergent designed for automatic dishwashers. Measure detergentcarefully. Try a different brand. • Spilled rinse aid can cause foam and leadto overflowing. Wipe up any spills with adamp cloth. • Check to see that dishwasher is level. (See Installation Instructions.) Normal Sounds You Will Hear • Normal sounds include water fill, water circulation and motor sounds. • There is a noticeable change in sound when the wash action switches between the lower and middle spray arm. This is normalsince each spray arm has its own sound. • It is normal for dishwasher to pause (nosound) when the wash action is switching between the lower and middle spray arms. Water in Bottom of Tub • Water left in bottom of tub after cycle iscomplete is not normal. If water remains in the bottom of the tub, dishwasher may notbe draining properly. (See Dishwasher DoesNot Drain Properly.) Vapor at Vent • Water vapor escapes from the vent duringthe drying part of cycle. This is normal. Dishwasher Won’t Run • Check to see if circuit breaker is tripped or ifa fuse is blown. • Make sure water supply is turned on. • Check to see if cycle is set correctly. (See Operating Instructions.) • Is dishwasher set for delay start option? • Make sure door is closed and latched. 16 Solutions to Common Dishwashing Problems (continued) Dishwasher Does Not Drain Properly • If unit is hooked up to a food waste disposer, make sure the disposer is empty. • Check to see if the knockout plug has beenremoved from inside the food waste disposer inlet. • Check to see if drain hose is kinked. • Make sure cycle is complete, not in a pause. Cycle Takes a Long Time • Is cycle in a water heating delay? • Has the delay start option been selected? Dishwasher Won’t Fill • Is water supply turned on? • Does overfill protector move up and downfreely? (See...