Оценок - 3, средний балл: 4 ( )

Производитель: Jackson Размер: 6.45 mb Название файла: Язык инструкции:

Ensure that the exhaust system is acceptable in accordance with all applicable codes and standards. NOTE: Any damage that is caused by steam or moisture due to improper ventilation is NOT covered under the warranty. This units covered in this manual have the following exhaust requirements: Load End: 200 CFM Unload End: 400 CFM The exhaust system must be sized to handle this volume for the dishmachine to operate as it was designed to. Incoming Power Connection AJ-44T Series Technical Manual 7610-003-07-21 Issued: 03-21-2006 Revised: N/A 27 SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS INSTALLATION INSTRUCTIONS (CONTINUED) ELECTRIC HEAT: The thermostats for the machines covered in this manual are factory set. They should not be adjusted except by an authorized service agent. CHEMICAL FEEDER EQUIPMENT: Detergent may be introduced into the unit through the removal of the bulkhead plug in the rear of the tub and replacing it with the third party detergent injection fitting. Remove the bulkhead plug in the side of the tub to install the detergent concentration probe. For more information concerning detergent concerns, please refer to the page entitled “Detergent Control”. Detergent Connection Point (Machine rear view) Brass Plug The 1/8” brass plugs on the incoming plumbing rinse injector may be removed to install sanitizer and rinse aid injection fittings. Brass Plugs All wires for the chemical injectors should be routed through one of the extra openings in the back of the control box. Terminals in the control box marked “CVS” provide a constant voltage signal whenever the drive motor is operating. Terminals in the control box marked “DET” provide a voltage signal whenever the wash motor is operating. Back of Control Box Aid Connection Points AJ-44T Series Technical Manual 7610-003-07-21 Issued: 03-21-2006 Revised: N/A 28 SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS CURTAIN INSTALLATION DIAGRAMS Please refer to the chart for placement of the curtains. AJ-44T Series Technical Manual 7610-003-07-21 Issued: 03-21-2006 Revised: N/A 29 ELECTRIC & STEAM MACHINES 44 UNHOODED SIDE LOADERHOODED SIDE LOADER LSLLSSLLSLSLLS 21" 12" 21" 21" 12" 12" 21" 21" 12" 21" 12" 21" 21" 12" L RL RL R 66 80 UNHOODED SIDE LOADER HOODED SIDE LOADER LSSL LSSSL LSLSSL LS 21" 12" 12" 21" 21" 12" 12" 12" 21" 21" 12" 21" 12" 12" 21" 21" 12" L RL RL R SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS DELIMING OPERATIONS DELIMING OPERATIONS: In order to maintain the dishmachine at its optimum performance level, it will be required to remove lime and corrosion deposits on a frequent basis. A deliming solution should be available from your detergent supplier. Read and follow all instructions on the label of the deliming solution. To proceed with the deliming operation, fill the dishmachine and add the correct amount of deliming solution as recommended by the deliming solution manufacturer. The water capacity of the various tanks of the dishmachine can be verified on the specification sheet(s) of this manual. Perform the following operations to delime the dishmachine: 1. Turn the NORMAL/DELIME switch on the back of the control box to the DELIME position. 2. Disconnect or turn off all chemical feeder pumps. 3. Close all doors (after adding the deliming solution). 4. Run the machine for the recommended period of time. 5. Turn the unit off and open the doors. 6. Wait five minutes, then inspect the inside of the machine. If the machine is not delimed, run another time cycle as per the deliming solution’s instructions. 7. When clean, drain and re-fill the machine. 8. Run in MANUAL for 10 minutes to remove residual deliming solution. 9. Drain and re-fill the machine. This equipment is not recommend for use with deionized water or other aggressive fluids. Use of deionized water or other aggressive fluids will result in corrosion and failure of materials and components. Use of deionized water or other aggressive fluids will void the manufacturer's warranty. AJ-44T Series Technical Manual 7610-003-07-21 Issued: 03-21-2006 Revised: N/A 30 SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS SIDE LOADER INSTALLATION & OPERATION INSTRUCTIONS This accessory assists in the delivery of a full dish rack from the break down (scrapping) table to the dishmachine. It will convert the direction of travel 90°. Since the Side Loader is shipped mounted on the conveyor dishwasher there is no additional installation required for this option. As it is operated mechanically by the dishwasher it does not require any plumbing or electrical connections. This Side Loader does not require or add any additional electrical or mechanical devices to the unit which could create operational or maintenance problems. As designed the drive mechanism is powered by the conveyor drive motor on the dishmachine. An extension on the pawl bar provides the drive to push the racks into the unit. PREPARATION: Before proceeding with the start-up of the unit, verify that the Side Loader pan strainer is inst...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: