Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
• The handle should be installed so that it aligns with adjacent drawer handles, or 4-1/2" max. from the top of the panel. Secure the handle in the same manner as cabinet handles. Screws must be countersunk into the panel. STEP 6 INSTALL ASSEMBLED PANEL • Secure the panel to the door by inserting the top and bottom mounting screws with spacers into the matching keyhole slots. • Make sure all 4 spacers engage the keyhole slots. • Press the panel against the door and push downward until the spacers are fully engaged into the key hole slots. The panel should align evenly with the top and sides. STEP 3 ALIGN TEMPLATE TO PANEL • Trim template on the dotted line along all sides. • Place the template on the panel aligned with the top edge and the centerline. Use tape to hold in place. IMPORTANT: If the template is not aligned with the top edge of the panel, the 1/2" minimum gap will not be maintained. This 1/2" minimum gap must be maintained to prevent condensation and damage to the control panel from screw heads. • Use an awl to mark the screw hole locations indicated on the template. Remove the template. HEIGHT Panel height must be between 30-1/16" and 30-1/4". PARTS INCLUDED: (4) Spacers (4) #8 x 5/8" Phillips truss head stainless steel screws (3) #8 x 1-3/4" Phillips truss head stainless steel wood screws (2) Heavy duty springs STEP 1 CUSTOM PANEL SIZE REQUIREMENTS If the panel is less than 3/4" thick, shorter screws must be used. Use #8 x 1/2" screws for 1/2" thick panels (not supplied). • Use a 3/32" drill bit to drill pilot holes 3/32" deep in the marked locations. Note: The custom panel is secured to the dishwasher door with the spacers and screws provided. The spacer will slip into the keyhole slots on the dishwasher door. • Drive the supplied #8 x 5/8" Phillips truss head steel screws through the spacer and into the panel. • Install remaining spacers and screws as indicated in the marked locations. 4-1/2" Max. From Topof Panel Handle Custom Door Panel Screws Must Be Countersunk Into Panel Custom Panel Shoulder Washers Engage Keyhole Slots Dishwasher Door Screw Spacer STEP 7 INSTALL DOOR SPRINGS The dishwasher is shipped from the factory with a temporary set of balance springs. Use the heavy duty springs provided and the adjustment holes in the cable to balance the door after the custom panel is installed onto the dishwasher. • With the dishwasher on the wood skid, close and latch the door. • Remove and discard both door springs. • Attach the new heavy duty door springs. Engage the end with the short hook into the support leg and the long hook into the cable. • Open and close the door. • If the door drops open when released, increase spring tension. If the door closes when released, decrease tension. TIP: If the door does not open easily or falls too quickly, check spring cable routing. The cable is held in place by “shoulders” on the pulley. Check to be sure the cable has not slipped over the pulley shoulders. IMPORTANT: Adjust both balance springs to the same amount of tension to prevent excessive door twisting during use. Correct Spring Cable Routing Increase Tension Decrease Tension Pulley Shoulder Use This Mounting Hole 23-3/4" • The top of the custom panel must be flush with the top of the door. The 1/2" minimum gap For Reference Only Not to Scale Trim Around Dotted Line Trim Around Dotted Line Order GE Pub. No. 31-30569-1 CALL 1-800-626-2000 For a full-size panel template with complete panel installation instructions. Specification Revised 2/08 150048 ZBd0710NSS/ZBd0700NII GE Monogram® Fully Integrated Built-In dishwasher Features and Benefits • Stainless Steel Interior • High-intensity Xenon Interior Lighting • End-of-cycle Indicator Light (ZBd0710NSS Model only) • Integrated Controls handle kit • Complete Cleaning Coverage – 3 wash arms, 6 wash levels • ultraquiet operation • Powerful, Forced-air drying System • Extra-tall Tub • Towerless Adjustable Rack System • ENERGY STAR® Qualified • Model ZBd0710NSS – Stainless steel • Model ZBd0700NII – Requires custom panel • Accessory: ZPRo0700S – Professional-style stainless steel door panel kit • Accessory: ZTB700 – Stainless steel tubular ZBD6890NII ZBD0700NII Specification Revised 2/08 150048 ...
Эта инструкция также подходит к моделям:Посудомоечные машины - ZBd0700NII (203.01 kb)