Оценок - 2, средний балл: 3 ( )

Производитель: GE Monogram Размер: 678.39 kb Название файла: Язык инструкции:

• Remove the four leveling legs on the underside of the wood base with an adjustable wrench or 15/16" socket. • Discard base. • Screw leveling legs back into the dishwasher frame, approximately 1/4" from frame as shown. STEP 2 REMOVE TOEKICK • Remove the two toekick screws. STEP 3 Toekick Remove 2 Toekick Screws Figure H Approx. 1/4" Figure J INSTALL POWER CORD Use Power Cord Kit WX09X70910 available for purchase from an authorized GE Appliances dealer. Skip this step if dishwasher will be direct wired or has a factory installed power cord. The power cord and connections must comply with the National Electrical Code, Section 422 and/or local codes and ordinances. • Maximum power cord length is 4 feet beyond the back of the dishwasher. • Connect incoming power cord white (or ribbed) to dishwasher white, black (or smooth) to black and ground to dishwasher green wire. Use UL listed wire nuts of appropriate size. • Replace junction box cover. Be sure wires are not pinched under the cover. STEP 4 White Ground Black Check That White, Black and Green Dishwasher Wires Are Threaded Thru Small Hole in Bracket Remove Junction Box Cover Insert Power Cord Wires Thru Strain Relief and Tighten Use UL Listed Wire Nuts A C B D Figure K INSTALL 90° ELBOW • Wrap 90° elbow with thread seal tape. • Install a 90° elbow onto the water valve. • Do not overtighten 90° elbow, water valve bracket could bend or water valve fitting could break. • Position the end of the elbow to face the rear of the dishwasher. STEP 5 Front of Dishwasher 90° Elbow Thread Seal Tape Fill Hose Water Valve Bracket Figure L 8 Installation Instructions STEP 6 POSITION WATER LINE AND HOUSING WIRING • Position water supply line and house wiring on the floor of the opening to avoid interference with base of dishwasher and components under dishwasher. 4" 5" 5" 4" 6" House Water Wiring Figure M Line STEP 7 INSTALL DRAIN HOSE, GUIDE THROUGH CABINET • Remove tape and wire tie holding the clamp to the drain hose. Be careful not to damage the drain hose. • Stand the dishwasher upright. • Slip the supplied Drain Shoulder Outlet hose clamp over Stop the large end of the hose. Do not tighten. Hose Clamp Flapper Valve—Do Not Remove Figure N • Push hose over the drain outlet on the back side of the dishwasher. See illustration. Push the hose over the outlet and against the shoulder stop. • Tighten the hose clamp with a 1/4" nut driver. Insulation Blanket Water Line Drain Hose House Wiring Figure O Power Cord (If Used) • Position the dishwasher in front of the opening. Insert drain hose into the cabinet side. If power cord is used, guide the end through a separate hole. 9 STEP 8 SLIDE DISHWASHER PARTIALLY INTO CABINET DO NOT PUSH AGAINST FRONT PANEL WITH KNEES. DAMAGE WILL OCCUR. • Slide dishwasher into the opening a few inches at a time. Reposition Dishwasher by Grasping Both Sides With Hands Do Not Push Against Front Door Panel With Knee. Damage to The Figure P Door Panel Will Occur. • As you proceed, pull the drain hose through the opening under the sink. Stop pushing when the dishwasher is a few inches forward of adjacent cabinetry. • Make sure drain hose is not kinked under the dishwasher and there is no interference with the water line and wiring or any other component. STEP 9 INSTALL TRIM PIECES Skip this step if trim is not supplied with the dishwasher. • Locate trim strips inside dishwasher. • Press trim onto the tub flange on each side. Start with the top edge, pressing on as you move towards the bottom. • Press the two top trim pieces on each side of the latch. • Open and close the door to check that trim does not bind and does not interfere with door latch. Trim Strip Trim Strip Trim Strip Figure Q Installation Instructions POSITION DISHWASHER UNDER COUNTERTOP STEP 10 • Push the dishwasher into the cabinet. • Push at the sides with your hands. Do not use your knee against the door since door damage will occur. • Check that the tub insulation blanket does not get “bunched-up” or interfere with the springs as you slide it into the cabinet. • Center the dishwasher in the opening. • Check that the edges of the dishwasher door are behind the cabinet frame and aligned with the front face of the cabinet as shown. • Carefully open and close the door to ensure that the door panel does not catch or rub on the cabinet frame. • If the door catches or rubs on the frame, reposition and/or level the unit (see Step 11) until the door moves freely and does not contact the cabinet frame. The controls are designed to be hidden by your countertop. Align the dishwasher as shown in Figure T. NOTE: If the drain hose gets trapped between the wall and the back side of the dishwasher, it can prevent the dishwasher from sliding all the way back into the cabinet opening, and thus preventing a flush fit with the kitchen cabinet panels. TIP: For best appearance installations of custom panel models, it may be necessary to cut off the back panel of the tub insulation blanket so that the dishw...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: