Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
If the appliance is partially loaded and the dishes lightly soiled, the "prewash", "main wash", and "rinse" phases of the programme are shorter and the water consumption level is lower. If the appliance is fully loaded and the dishes heavily soiled, the "prewash", "main wash", and "rinse" phases of the programme are longer and the water consumption level is higher. During the "Automatic" programme the temperature of the main wash water is also automatically adjusted between 50°C and 65°C depending on the amount of soil on the dishes. (2) Ideal for washing crockery and cutlery of breakfast and dinner (fresh soil). Characterised by a short duration. This is the perfect daily programme, made to meet the needs of a family of 4 persons who only wish to load breakfast and dinner crockery and cutlery. (3) Testing programme for EN 50242 (see "Hints for Test Centres").This programme, developed for the use of detergents with enzymes, allows you to achieve, with reduced consumption of energy the same cleaning results that would otherwise be obtained only with the 65°C programmes and conventional detergents.To compensate the lower temperature, the duration of washing and drying have been extended. (4) The consumption values are intended as a guide and depends on the pressure and the temperature of the water and also by the variations of the power supply. The programme duration is visible in the display when the setting of the programme occurs. 20 Starting a washing programme In this fully integrated appliance the controls are located on the top of the door.When selecting a programme, the door needs to be open. 1. Check that the baskets have been loaded correctly and that the spray arms can rotate freely 2. Turn on the water tap 3. Press the On/Off button The indicator lights of the programme selection buttons illuminate. 4. Setting and starting the programme To select a programme, press the button of the programme you wish to select (see "Washing programmes" chart). The corresponding indicator light remains illuminated while the other programme buttons indicator lights turn off. In the digital display will appear, flashing, the running time (in minutes) of the programme that has been set. Close the dishwasher’s door, the programme will start automatically. Setting and starting the programme with the delay start Once the washing programme has been selected press the delay start button, the corresponding indicator light will illuminate and 1h appears in the digital display. Press the delay start button until the number of hours desired (from 1 hour up to 19 hours) appear in the digital display. Close the dishwasher door, the countdown starts automatically and will decrease with steps of 1 hour. The opening of the door will not modify or interrupt the countdown. Once the delay start has elapsed the washing programme will start automatically. NOTE: The start of the programme or the countdown of the delay start will occur only after the closure of the door, until this moment it is possible to modify the set made. NOTE: Once the washing programme has started, a point-shaped optical signal appears on the floor beneath the dishwasher’s door.This optical signal will remain illuminated for all the duration of the washing programme. If the appliance has been installed higher up with a furniture door mounted flush, the optical signal will be no longer visible. 5. To interrupt or cancel a washing programme in progress Interrupt or cancel a washing programme in progress ONLY if it’s absolutely necessary. Important! Hot steam may escape when the door is opened. Open the door carefully. Interrupt a washing programme in progress Open the dishwasher door; the programme will stop. Close the door; the programme will start from the point at which it was interrupted. Cancel a washing programme in progress Open the dishwasher door. Press simultaneously function buttons 2 and 3 for about 2 seconds, the indicator light of the button corresponding to the running programme starts flashing.After about 2 seconds the indicator lights of all the programme selection buttons will illuminate, this means that the running programme has been cancelled and that the machine has returned to setting mode. If a new washing programme is to be selected, check that there is detergent in the detergent dispenser. 6. To cancel a delay start in progress To cancel a delay start in progress you have to reset the dishwasher; follow the same instructions given in "Cancel a washing programme in progress". Cancelling a delay start involves also the cancelling of the set washing programme. In this case you have to set the washing programme again. 7. End of the washing programme The dishwasher will automatically stop and an audible signal informs you of the end of the washing programme. When the washing programme has ended, the optical signal on the floor beneath the dishwasher’s door will turn off. Open the dishwasher door only when this optical signal turns off. Open the d...