Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Make sure that the connection is correct. The water inlet hose is damaged. Make sure that the water inlet hose has no damages. The appliance does not drain the water. There is a blockage in the sink spigot. Clean the sink spigot. The connection of the water drain hose is not correct. Make sure that the connection is correct. The water drain hose is damaged. Make sure that the water drain hose has no damages. The anti-flood device is on. Close the water tap and contact our extended warranty administrators. Refer to 'Repairs - after sales service'. The start of the washing programme does not occur. The appliance door is open. Close the appliance door. The mains plug is not connected in the mains socket. Connect the mains plug. The fuse in the fuse box is damaged. Replace the fuse. 24 Malfunction Possible cause Possible solution The delay start is set. • Cancel the delay start. • When the countdown is completed, the washing programme starts automatically. Once the checks have been carried out, If the malfunction occurs again or the display switch on the appliance. The programme shows an alarm code that is not listed in the continues from the point at which it was table, please contact our extended warranty interrupted. administrators. Refer to 'Repairs - after sales service'. The washing and drying results are not satisfactory The dishes are not clean. The washing programme was not applicable for the type of load and soil. Make sure that the washing programme is applicable for the type of load and soil. You did not put the items correctly in the baskets, water did not touch all surfaces. Put the items correctly in the baskets. The spray arms could not turn freely. Incorrect position of the items in the baskets. Make sure that an incorrect position of the items do not cause the blockage of the spray arms. The filters are dirty or not assembled and installed correctly. Make sure that the filters are clean and correctly assembled and installed. The quantity of detergent was not sufficient or missing. Make sure that the quantity of detergent is sufficient. Limescale particles on the dishes. The salt container is empty. Fill the salt container with dishwasher salt. Incorrect level of the water softener adjustment. Adjust the water softener with the correct level. The salt container cap is not closed correctly. Make sure that the salt container cap is closed correctly. There are streaks, whitish stains, or a bluish layer on glasses and dishes. The rinse aid quantity is too high. Decrease the rinse aid quantity. Dry water drop stains on glasses and dishes. The rinse aid quantity is too low. Increase the rinse aid quantity. 25 The washing and drying results are not satisfactory The detergent can be the cause. Use a different brand of detergent. The dishes are wet. The washing programme was without a drying phase or with a decreased drying phase. For better drying results, keep the door ajar for some minutes. The dishes are wet and matt. The rinse aid dispenser is empty. Fill the rinse aid dispenser with rinse aid. The Multi tab function is on (this function automatically deactivates the rinse aid dispenser). Activate the rinse aid dispenser. Activating the rinse aid dispenser 1. Switch on the appliance. The appliance must be in setting mode. 2. Press and hold function button (B) and function button (C) simultaneously until the indicators above function buttons (A), (B) and (C) start to flash. 3. Release function button (B) and function button (C). 4. Press function button (B), the indicators above function buttons (A) and (C) go off while the indicator above function button (B) continues to flash. The display shows the current setting. Rinse aid dispenser deactivated Rinse aid dispenser activated 5. Press function button (B) again. The display shows the new setting. 6. Switch off the appliance to confirm the operation. 26 Technical data Dimensions Width 596 mm Height 850 mm Depth 597 mm Water supply pressure Minimum 0.5 bar (0.05 MPa) Maximum 8 bar (0.8 MPa) Electrical connection Information on the electrical connection (voltage, overall power and fuse) is given on the rating plate on the inner edge of the appliance door. Capacity Place settings 12 Installation Warning! It is dangerous to alter the specifications or attempt to modify the appliance in any way. Warning! This appliance is heavy. Care should be taken when moving it. Warning! Care must be taken to ensure that the appliance does not stand on the electrical supply cable. Warning! Any electrical or plumbing work required to install this appliance must be carried out by a qualified electrician or plumber. Unpacking • Remove all packaging before positioning the appliance. • Position the appliance next to a water tap and a drain. Fitting under the kitchen worktop By removing the worktop of the appliance , you can install it under the kitchen worktop or a close fitting sink. The dimensions of the recess must correspond to those shown in the picture. 27 Removing t...