Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
WARNING This dryer is equipped with a three-prong (grounding) plug for your protection against shock hazard and should beplugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug. W036 WARNING Improper connection of the equipment- grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the dryer is properly grounded. W038 Do not modify the plug provided with the dryer – if it will not fit the outlet, have a proper outlet installed by a qualified electrician. NOTE: Have a qualified electrician check the polarity of the wall receptacle. If a voltage reading is measured other than that illustrated, the qualified electrician should correct the problem. Do not operate other appliances on the same circuit when this appliance is operating. 802715 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 19 WARNING To reduce the risk of an electric shock or fire, DO NOT use an extension cord or an adapter to connect the dryer to the electrical power source. W037 Washer - All Models Except LTSA7A*N2989 Washer requires 120 Volt, 60 Hertz electrical supply and comes equipped with a 3-prong grounding plug. Refer to serial plate for specific electrical requirements. NOTE: The wiring diagram is located behind the control panel, inside the control cabinet. DRY2022N 1 “L1” 2 Ground 3 Neutral 4 Neutral Side 5 Round Grounding Prong Figure 26 0 V.A.C 120±12 V.A.C Plug cord into separately fused 15 Amp circuit. 3 2 1 4 5 120±12 V.A.C 1 2 3 4 5 Standard 120 Volt, 60 Hertz 3-Wire EffectivelyGrounded Circuit 0 V.A.C. 120±12 V.A.C. 120±12 V.A.C. 1 2 3 4 5 L1 Ground Neutral Side Round Grounding Prong Neutral DRY2022N Figure 27 To reduce the risk of fire, electric shock, serious injury or death, all wiring and grounding MUST conform with the latestedition of the National Electrical Code, ANSI/NFPA No. 70, and such local regulations as might apply. It is thecustomer’s responsibility to have the wiring, fuses and circuit breakers installed by a qualified electrician to makesure adequate electrical power isavailable to the washer. W518 WARNING 20 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802715 When plugging in the washer: • DO NOT overload circuits. • DO NOT use an extension cord. • DO NOT use an adapter. • DO NOT operate both a washer and gas dryer on the same circuit. Use separately fused 15 Amp circuits. The washer is designed to be operated on a separate branch, polarized, three-wire, effectively grounded, 120 Volt, 60 Hertz, AC (alternating current) circuit protected by a 15 Amp fuse, equivalent fusetron or circuit breaker. The three-prong grounding plug on the power cord should be plugged directly into a polarized three-slot effectively grounded receptacle rated 110/120 Volts AC (alternating current) 15 Amps. Refer to Figure 27 to determine correct polarity of the wall receptacle. To reduce the risk of an electric shock or fire, DO NOT use an extension cord or an adapter to connect the washer to the electric power source. W082 WARNING Grounding Information The washer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. The washer is equipped with a cord having an equipment-grounding conductor and a 3-prong grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. WARNING Improper connection of the equipment- grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the washer is properly grounded. W216 NOTE: Have a qualified electrician check the polarity of the wall receptacle. If a voltage reading is measured other than that in Figure 27, the qualified electrician should correct the problem. WARNING This unit is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug. W213 Step 11: Recheck steps 1-10 Refer to Installer Checklist on the back cover of this manual and make sure that unit is installed correctly. Run washer through one complete cycle to make sure it is operating properly. Step 12: Check Heat Source Electric Dryers Close the loading door and start the dryer in a heat setting (refer to the Dryer User’s Guide supplied with the unit). After the dryer has operated for three minutes, the exhaust air or exhaust pipe should be warm. Gas Dryers IMPORTANT: This operation is to be conducted by qualified personnel only. To view the burner flame, remove the lower front panel of the dryer. Close the loading door, start the dryer in a heat setting (refer to the Dryer User’s Gui...