Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
The float must be in place for the dishwasher to operate. Important: A small amount of water always remains in the bottom of the dishwasher (under the ultrafine filter) to keep the seal moist. The coarse strainer may be removed, if necessary. To remove, lift strainer out by squeezing center section (F) and remove. To replace, squeeze center section so clips snap into square notch. Possible Burn Hazard Heating element will be hot immediately following use. Do not touch. To avoid burns wait at least 20 minutes after a cycle for the heating element to cool down. 17 Problem-, Cause, Solution Chart A convenient checklist for handling minor performance problems. Go over this list before calling for service. If you can't solve your dishwasher's problem, turn to page 23 for service information. PROBLEM CAUSE SOLUTION Food Soil Left On Dishes Slowdown of wash arm due to high suds Use recommended dishwasher detergents only. Never use soap or laundry detergents. Add more dishwasher detergent to increase amount of suds-inhibitors. Improper loading Follow loading instructions in dishwasher Use and Care Guide. Low water pressure due to insufficient fill Home water pressure should be 20 to 120 psi for proper dishwasher fill. A booster pump on the water supply may be necessary if pressure is too low. Use of incorrect, too little or ineffective detergent Use recommended dishwasher detergents only. Follow recommendations in Use and Care Guide for amounts; never use less than one tablespoon per load. Detergent must be fresh to be effective. Always store it in a cool, dry area, preferably in an airtight container. Detergent cakes in dispenser Use fresh detergent only. Do not allow detergent to sit for several hours in a wet dispenser. Have dispenser checked to make sure it is working properly. Water temperature is too low Turn home water heater up so water entering dishwasher is I40°F (60°C) minimum. Do not select ENERGY SAVER-NO HEAT, Filter cleaning spray nozzle on wash arm is blocked Remove lower wash arm and turn upside down. Check single stainless steel spray nozzle and nine water jets located on underside of wash arm. See page 16. Check to make sure openings are not blocked. Spotting and Filming Hard water or high mineral content in water Conditioning the final rinse water with a liquid rinse agent helps eliminate spotting and filming. See page 14. Water temperature is too low Turn home water heater up so water entering dishwasher is I40°F (60°C) minimum. Do not select ENERGY SAVER-NO HEAT. Use of incorrect detergents Use recommended dishwasher detergents only. Incorrect amount of detergent Follow recommendations in dishwasher Use and Care Guide for amount. Heavy soil and/or hard water generally require extra detergent. Use of ineffective detergents Detergent should be fresh. Store in a cool, dry place, preferably in an airtight container. Discard lumpy detergent. Insufficient fill caused by low water pressure Home water pressure should be 20 to 120 psi for proper dish washer fill. A booster pump on the water supply may be necessary if pressure is too low. Dishes Do Not Dry Completely Dishes do not drain properly Dishes must have proper water drainage. Do not overload. Follow instructions for loading in dishwasher Use and Care Guide. Use a liquid rinse agent to speed draining. Plastics Some plastics, due to material, may need to be towel dried. Silica Film or Etching (Silica Film is a White Iridescent Deposit; Etching is a Cloudy Film) A water chemical reaction with certain types of glassware. Usually caused by some combination of soft or softened water, alkaline washing solutions, insufficient rinsing, overloading the dishwasher, and heat of drying. It may not be possible to prevent problem, except by hand washing. To retard this process, use a minimum amount of detergent but not less than one tablespoon per load. Use a liquid rinse agent and underload the dishwasher to allow thorough rinsing. Silica film and etching are permanent and cannot be removed. Use ENERGY SAVER DRY. 18 Changing Front Panels Your new KitchenAid dishwasher comes with a stainless steel trim kit and one front and lower reversible panel. You can choose from black or white. If you want to change the color of the panels, follow one of the options below: OPTION A may be used if your dishwasher front sticks out several inches from the cabinets. OPTION B may be used if your dishwasher front is flush with the cabinets. Electrical Shock Hazard Disconnect electrical power supply to dishwasher before changing panels. Failure to do so could result in electrical shock or personal injury. OPTION A Upper Panel: 1. Disconnect electrical power supply. 2. Pull door open and on either side of the dishwasher door, remove the three screws (A) from the trim (B). Remove the loosened piece of trim. 3. Slide the color panel out. Handle carefully so the panel will not be scratched or bent. Turn the panel to the desired color. ...
Эта инструкция также подходит к моделям:Посудомоечные машины - KUDB22HT (1.41 mb)