Оценок - 3, средний балл: 5
(
)
)
|
Фрагмент инструкции
OBSERVE ALL LISTED WARNINGS AND CAUTIONS. For Replacement Installation -Review these complete instructions to be sure that previous connections are compatible. For New Installations -Plumbrng and electrical connections must be provided before the dishwasher is moved Into place. These instructions are intended for use by qualified workers who will observe all local codes and ordinances for plumbing connections as well as local codes and/or the Canadian Electrical Code for’electrical connections. DO NOT REMOVE THE GALVANIZED STEEL SIDE AND BOTTOM PANELS. THE REMOVAL OF THESE ITEMS WILL VOID THE C.S.A. CERTIFICATION AND INCREASE THE DANGER OF FIRE AND ELECTRICAL SHOCK. I YOU WILL NEED THESE TOOLS: Phillrps Screwdriver Flat Blade Screwdnver Adjustable Wrenches (2) (if copper fittings are used) Pipe Wrenches (2) (if galvanized or iron fittings are used) Nut Driver or Socket Set Wrre Cutters Tape Measure Spirit/Bubble Lever Electrrc Drrll 1” (25 mm) Drill BII or Hole Saw 58 (3 mm) Drill Bit Square . . . AA/D THESE MATERIALS: 5/a” (16 mm) OD Copper Tubing (of sufficient length for your installation), Shut-off Valve, and Fittings (for copper water supply line) l/i” (13 mm) Pipe (of sufficient length for your installation), Shut-off Valve, and Fittings (for galvanized water supply line) %I” (9.5 mm) NPT 90° Street Elbow 90° Compression Elbow: l/z” (13 mm) Tube End & 3/e” (9.5 mm) NPT male pipe end (for copper water supply line only) See Fig. 13 page 10. l/2” (13 mm) NPT 90° Street Elbow and l/2” (13 mm) NPT female x 3/a” (9.5 mm) NPT male reducing adapter (for galvanized water supply line only) 9/,6” (14 mm) ID Heat and Detergent Resistant Rubber Hose and Clamps or s/a” (16 mm) OD Copper Tubing and Fittings (of sufficient length to accommodate your drain line) 10” (250 mm) Length of 518” (16 mm) OD Soft Copper Tubing, Formed Into a Semicircle (if high loop drain is required -see page 7) 115 Volt, 15 Amp, 2 Wire, Properly Grounded, Branch Circuit x/4” (19 mm) Strain Relief Bushing for Electrical Supply Cable. -3- SPECIFICATIONS Electrical 115 volts 60 hertz 1 phase Operating Load 13.5 amperes Maximum Protective Device Size 15 amperes Minimum Circuit Size 15 amperes Water Temperature 120°F (49°C) minimum at dishwasher Water Pressure (Flowing) 20 to 120 psi (138 to 827kPa) Cabinet Opening 337/16” (849 mm) to 35” (889 mm) high 24” (610 mm) wide 24” (610 mm) deep (min.) HERE ARE THE BASIC STEPS OF INSTALLATION: Page 1 CHOOSING THE LOCATION 5 2 PREPARING THE LOCATION 3 PLACING THE DISHWASHER IN ITS LOCATION 4 CONNECTING THE WATER SUPPLY LINE 10 5 CONNECTING THE DRAIN LINE 11 6 CONNECTING THE ELECTRICAL SUPPLY 11 7 FINAL CHECK LIST .., 12 8 FRONT PANEL VARIATIONS .., 13 9 SEASONAL STORAGE 14 -4- I CHOOSING THE LOCA T/ON For easy access to plumbing, it is most convement to have your dishwasher located near the kitchen sink. Any built-in dishwasher must be fully enclosed on the top, both sides, and the back. Therefore, the cabinet space below your kitchen counter is probably the best location. If the dishwasher is being installed at the end of a cabinet or free standing then side panels and a wood top can be purchased from your KitchenAid dealer to enclose the dishwasher. The cabinet opening (Fig. 1) should be square with dimensions as follows: Height -3311/,6” (856 mm) to 35” (889 mm); Width -24” (610 mm) minimum; Depth -24” (610 mm) minimum. If the dishwasher height of 33”/ ,6” (856 mm) is too high, it may be reduced to 337h6” (849 mm) by removing the leveling feet. If side panels are used, cabinet height should be 34%” (876 mm) minimum to 35” maximum using the adjusting legs. ) 0 I .i[ 1 p. I DISHWASHER COUNTERTOP .D * I-‘1 337/,6” thru 35” ‘I (849-889 mm) I-Clearance for door openmg 2” (51 mm) minimum 3 1 Fig. 2 If the drshwasher IS installed in a corner, there must be adequate clearance to open the door (Fig. 2) I I To protect against possible rupture of the fill valve, water lines leading to the dishwasher, as well as water lines in the dishwasher MUST be protected against freezing. Such ruptures are not covered by the warranty. I -5- PREPARING THE LOCATION Access holes in the cabmets, floor, or rear wall for the hot water supply line, drain line, and electrical supply must be located within the shaded area in Fig. 3 in order to avoid Interference with the dishwasher frame or other components. HOT WATER SUPPLY LINE Fig. 3 PLUMBING CONNECTIONS MUST COMPLY WITH APPLICABLE SANITARY, SAFETY, AND PLUMBING CODES. Water supply should be 120°F (49OC) minimum at the dishwasher. (Refer to Use & Care Guide.) The hot water supply line should be 5%” (16 mm) OD copper tubing or l/2” (13 mm) galvanized pipe. The dishwasher fill valve has a l/z” (13 mm) NPT female connection. Atter determining where the water supply line will enter the dishwasher opening, drill a 1” (25 mm) access hole and run the line to the approximate fill valve location as shown in Fig. 4. 4” (102 mm) -(Frbm floor) 6” (152 mm) Fig. 4 For service convenience, a shu...