Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
8/91 42" SNOW PLOW/DOZER BLADE Mfg. No. 1691520 HITCH ASSEMBLY Mfg. No. 1692039 Contents SAFETY RULES ........................................................................... 2 PARTS ILLUSTRATION .................................................................... 3 ASSEMBLY, INSTALLATION & REMOVAL .................................................. 4 OPERATION AND NORMAL CARE ............................................. ........... 5 ADJUSTMENTS ........................................................................... 6 1 Safety Rules A Read these safety rules and follow them closely. Failure to obey these rules could result In loss of control of vehicle, severe personal injury to yourself or bystanders, or damage to property or equipment. The triangle & in the text signifies important cautions or warnings which must be followed. ALL WARNING, CAUTION, and instructional messages on this attachment and on yourtractor should be carefully read and obeyed. Personal bodily injury can result when these instructions are not followed. GENERAL • Read the operator’s manual carefully. Be thoroughly familiar with the controls and proper use of the equipment. Know how to stop the unit and disengage the controls quickly. • Never allow children to operate the machine. Do not allow adults to operate it without proper instruction. • Keep the area of operation clear of all persons, particularly small children, and pets. • Do not carry passengers. • Make sure: a. tractor and attachments are in good operating condition. b. all safety devices and shields are in place c. and in good working condition, and d. all adjustments (skid shoe height, etc.) have been made. PREPARATION • Handle gasoline with care — it is highly flammable. a. Use approved gasoline container. b. Never remove the cap of the fuel tank or add gasoline to a running or hot engine, or fill the fuel tank indoors. Wipe up spilled gasoline. • Do not run the engine indoors. Exhaust fumes are dangerous. • Shift into neutral before attempting to start the engine. • Wear proper footwear. Do not operate tractor when barefoot or when wearing open sandals or canvas shoes. OPERATION • Do not allow anyone to use the snow plow/dozer blade unless they have been instructed on how to operate it safely. • Never attempt to adjust, repair or service the snow plow/dozer blade while the tractor engine is running. • Do not allow others near the snow plow/ dozer blade while it is being used. • Use the snow plow/dozer blade only in daylight, or good artificial light. • Always lower the snow plow/dozer blade completely to the ground when leaving it unattended to prevent it from being accidentally lowered and causing injury. Make sure blade is locked in “DOWN” position due to spring-assist. • Always operate the tractor at reasonable speeds to prevent the blade from catching an object and stopping the tractor abruptly. 2 Parts Illustration Ref. No. Qty. Description Ref. No. Qty. Description Lift Rod Assembly Sprlng-Asslst Assembly A 2 COLLAR, Set L 1 CAPSCREW, Hex, 5/16-18 x 1 B 2 SETSCREW, 5/16-18 x 1/2 M 1 LOCKWASHER, 5/16 C 1 GUIDE ASSY., Rod N 1 NUT, Hex, Full, 5/16-18 D 1 SPRING O 1 PIN, Hitch E 1 ROD, Lift (Manual or Electric Lift) P WASHER, Plain, 5/16 F 3 CLIP, Spring Q 1 CHAIN, 4-Link Push Bar Assembly PIN, King BAR ASSY., Push CLIP, Safety PIN, Pivot ROD, Latch R S 1 1 SPRING BRACKET, Spring Anchor G 1 H 1 I 2 J 1 K 4 3 Assembly, Installation & Removal ASSEMBLY 1. Place the blade on a flat surface. 2. Insert eyebolt (A, figure 2) thru lug on blade and screw on 5/16 nut (B) onlyfarenough so that it is flush with the end of the eyebolt. 3. Hook the spring (C) into the pivot frame (D). Stretch the spring with a pliers to hook springs on eyebolt (A). Figure 2. Tension Springs A. Eyebolt B. Nut, 5/16 C. Spring D. Pivot Frame E. Nut, 5/16 4. Repeat steps 2 and 3 for the other spring. 5. Tighten the nut (B) on both eyebolts down to expose about 3/4 inch (19 mm) of thread. (See page 6 for spring tension adjustment.) 6. Add the other nut (E) to each eyebolt. Hold the first nut (B) secure with a wrench and tighten the second nut (E) securely on each eyebolt. NOTE On single cylindertractors, clevis pin (B,figure 3) must be installed to bracket before mounting bracket on tractor frame. 7. Install the spring-assist bracket (A, figure 3) to tractor frame (bracket is mounted underneath frame). Secure with capscrew (from top), lockwasher, and nut. Place clevis pin (B) through bracket and install flat washer, chain (C), flat washer, and safety clip. Figure 3. Install Spring Assist Bracket A. Bracket B. Clevis Pin C. 4-Link Chain INSTALLATION 1. Drive the tractor over the push bar until rear of push bar is under front hitch. 2. Stop engine, remove key and set parking brake. 3. Position the push bar hitch (A, figure 4) onto the tractor frame brackets (B). Secure push barwith pin (C) and safety clip (D). Figure 4...