Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
You should make sure that ample working area is around your tractor so that you will not be cramped for working space. It is suggested that you first remove all the shipping carton from around the loader so that all parts can be readily seen. Where reference is made to left or right side, this is determined by sitting on the tractor seat. You should have the following tools at hand: 2 - Open End or Box End Wrench 2 - 9/16” Open End or Box End Wrench 1 - 11/16” Open End or Box End Wrench 1 - 5/8” Open End or Box End Wrench 2 - %” Open End or Box End Wrench 2 - 15/16” Open End or Box End Wrench 1 - 5/32” Allen Wrench 1 - Medium Size Crescent Wrench 1 - Standard Screw Driver A set of Socket Wrenches if available. At this time unpack and lay aside all assemblies except the under frame and lift frame. BUCKET INSTALLATION Remove the shipping clamps from the lift frame and leave lift frame in position on pallet. Next, remove the bucket from its shipping container and locate the mounting brackets over the front mounting bushings on the front of the lift frame. At this time the mounting brackets on the bucket should be resting on the pallet as in Figure 1. FIGURE 1 Insert lift frame pins and lock in place with bushing, 3/8” x 3/4” bolt, FW and LW. At this time connect the tilt cylinders and bucket guide assembly to the top holes in the bucket mounting,-bracket. UPRIGHT INSTALLATION Next install the Left and Right Uprights P/N 250932 L & R to the lift frame and install lift frame pins and lock into place with bushing, 3/8” x 3/4” bolt, flat washer (FW) & lockwasher (LW). Attach the two lift cylinders to the uprights with the pins provided, and then install the Stabilizer Bar P/N 24052 with two (2) 3/8” x 1” bolts, LW, FW & nuts. Remove the Under Frame P/N 270950 from the pallet and then insert a dismount stand into each bushing on the front edge of each upright base with the base of the dismount stands towards the front. Then lift the whole assembly up until the unit is resting on the stands,Figure 2, and then remove the pallet from the area. FIGURE 2 PUMP MOUNTING INSTALLATION At this time raise tractor hood and disconnect the two (2) springs holding the battery cover down. Remove one (1) 5/16” x 1/2” bolt holding ground wires on the right side. Remove one (1) 3/8” x 5/8” bolt holding hydraulic line bracket on left side. Now, remove the pump guard from the pump assembly and also remove the nuts, bolts and lock washers located on the top of each pump mounting bracket. With the hood still in the raised position, place the pump assembly up to the tractor as shown in Figure 3. -8- FIGURE 3 Once in place insert bolts and install lock washers and nuts previously removed from the pump assembly and tighten securely. Re-install the ground wires and springs holding the battery cover. Loosen the 3/8” x 2” belt tightner bolt so that the pump mounting plate will have freedom of movement up and down and then from the top install the V-belt, P/N 23092 over the tractor P.T.O. pulley and then install V-belt on the pump pulley. Figure 4. FIGURE 4 Alignment of pump pulley with P.T.O. pulley can be obtained by loosening the set screws on pump pulley and sliding to desired position on the pump shaft. Be careful to leave clearance between the pulley and the pump housing. Tighten set screws and then tighten the belt with the belt tightner screw. Do not over-tighten. Do not install pump guard at this time. UNDER FRAME INSTALLATION The under frame, P/N 270950, for this heavy duty loader is the most difficult part to install for one person, however, it can be done. First, remove ;he lower brackets to which the three point hitch is mounted. Then remove all bolts, LW, FW & nuts from under frame and position the under frame under the tractor so that from the rear of the tractor you can lay on your back and lift the frame into position by getting your arm and elbow directly under to support while installing on either side in the rear slotted hole, one (1) V2” x 2V4” bolt, LW & FW. Give bolt three or four turns so that ¡t will stay. Next, install one (1) %'• x 2’A" bolt, LW & FW on the other side and at the same time reinstall on this side the three point hitch bracket previously removed, but do not install the other bracket at this time. Give this bolt three or four turns. At this time the under frame will appear as shown in Figure 5 and Figure 6. FIGURE 6 Next, turn wheels to the extreme right position and move to left or right side of tractor. Raise the front of the under frame to its full position and install the %"--x W bolt, LW & FW on both sides. (Note: Due to paint on both the tractor and under frame this may be a tight fit.) Next, reinstall the other three point hitch bracket and the remaining bolts, LW & FW in the rear of the under frame. When under frame installation is complete it will appear as in Figure 7. —9— FIGURE 7 (Note: If two persons are available it is easier to start the under frame installation...
Эта инструкция также подходит к моделям:Погрузчики - 1690157 (1022.17 kb)