Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
If any assistance or addi- tional information is needed, contact your authorized Bush Hog dealer. Bucket 1-2 DESCRIPTION The Models 2427 and 3227 Front End Loaders are designed for two wheel drive tractors. The Models 2447 and 2847 Front End Loaders are designed for two wheel and four wheel drive tractors. They come equipped with parking stands to support the loader so the tractor can be “driven in” for quick attachment and a bucket level indicator that allows operator to gauge bucket position when the bucket cannot be seen. Available attachments include buckets for lift- ing loose materials; a bale spear for lifting round hay bales; and a fork lift for palletized material. All opera- tions should be conducted within the loader limits specified in Table 1-1. IMPORTANT This manual covers four different models of front end loaders. There will be minor differences in configuration and appearance of some components. However, the basic assembly and operation of the different models will be the same. All references made to right, left, front, rear, top or bottom is as viewed facing the direction of travel with implement properly attached to tractor. 8 Table 1-1 TECHNICAL SPECIFICATIONS GEJCBAHFXXZZWXYZUVVV SERIES LOADER 2427QT 2447QT 2847QT 3227QT A. Maximum Lift Height -Measured at Pivot Pin 117 in. 117 in. 137 in. 143 in. B. Maximum Lift Height - Under Level Bucket 108 in. 108 in. 128 in. 134 in. C. Clearance with Attachment Dumped 45° 89 in. 89 in. 109 in. 115 in. D. Reach at Maximum Height 26 in. 31 in. 28 in. 28 in. E. Maximum Dump Angle 50° 50° 50° 50° F. Reach with Bucket on Ground 62 in. 65 in. 76 in. 73 in. G. Maximum Rollback Angle 25° 25° 25° 25° H. Digging Depth 4.5 in. 4.5 in. 5.5 in. 4.5 in. J. Overall Height in Carry Position 59 in. 66 in. 74 in. 69 in. U. Lift Capacity to Maximum Height - At Pivot Pin 2990 lbs. 2870 lbs. 3560 lbs. 4110 lbs. V. Lift Capacity to Maximum Height - 31.5” Forward of Pivot Pin 1920 lbs. 1985 lbs. 2475 lbs. 2800 lbs. W. Lift Capacity to 59” Height - At Pivot Pin 4130 lbs. 3220 lbs. 4090 lbs. 4410 lbs. X. Lift Capacity to 59” Height - 31.5” Forward of Pivot Pin 3020 lbs. 2390 lbs. 3105 lbs. 3360 lbs. Y. Breakout Force - At Pivot Pin 4985 lbs. 3955 lbs. 5030 lbs. 5160 lbs. Z. Breakout Force - 31.5” Forward of Pivot Pin 3500 lbs. 2940 lbs. 3630 lbs. 3730 lbs. VV. Rollback Force at Maximum Height - 31.5” Forward of Pivot Pin 2400 lbs. 3155 lbs. 4420 lbs. 4940 lbs. XX. Rollback Force at 59” Height - 31.5” Forward of Pivot Pin 3340 lbs. 3880 lbs. 5505 lbs. 6865 lbs. ZZ. Rollback Force at Ground Level - 31.5” Forward of Pivot Pin 2710 lbs. 3015 lbs. 4020 lbs. 5305 lbs. Raising Time - Ground Level to Full Height 6 sec. 4 sec. 7 sec. 5 sec. Lowering Time - Full Height to Ground 3 sec. 3 sec. 4 sec. 3 sec. Bucket Dumping Time - Full Rollback to Full Dump 3.5 sec. 4 sec. 5 sec. 5 sec. Bucket Rollback Time - Full Dump to Full Rollback 2 sec. 2.5 sec. 3 sec. 3 sec. Tractor HP Range 35 - 75 2 WD 35 - 75 2 & 4 WD 60 - 90 2 & 4 WD 70 - 120 2 WD Based On Tractor Hydraulic System: P r e s s u r e F lo w 2 4 5 0 p s i 1 1 g p m 2 4 5 0 p s i 1 1 g p m 2 4 5 0 p s i 1 1 g p m 2 4 5 0 p s i 1 6 g p m 9 SECTION II LOADER MOUNTING AND DISMOUNTING 2-1 PREPARING TRACTOR CAUTION TRACTORS THAT HAVE MOVABLE AXLES MUST BE SET FORWARD IN THE LONG WHEEL- BASE POSITION AS SHOWN IN FIGURE 2-1 TO PREVENT EXCESSIVE LEVERAGE BEING EXERTED ON THE TRACTOR FRAME. FAILURE TO DO SO CAN RESULT IN PERSONAL INJURY AND EQUIPMENT DAMAGE. REFER TO TRAC- TOR OPERATOR’S MANUAL FOR ABOVE PRO- CEDURES AND SPECIFICATIONS FOR YOUR TRACTOR. A. Check air pressure in tractor tires to be sure it is adequate for heavy loads. B. Add rear wheel weights, fluid in tires, or equiv- alent to provide sufficient tractor stability. C. It is recommended that tractor wheels be moved to the widest settings. D. Check tractor hydraulic oil reservoir to be sure it is full. E. Refer to your tractor operator’s manual for above procedures and specifications for your tractor. 2-2 MOUNTING LOADER A. Slowly drive tractor into loader. (Figure 2-2). WARNING LOADER HOSES MUST BE CONNECTED TO APPROPRIATE TRACTOR AUXIL- IARY OUTLET. FAILURE TO DO SO CAN RESULT IN PERSONAL INJURY. Figure 2-1ShortWheelbaseLong Wheelbase B. Connect hydraulic hoses to appropriate tractor auxiliary outlets. Verify proper connection of hoses by noting loader and bucket movement per decal on valve cover. Also control having “float” position should allow boom to “float” when pushed forward to detent. C. Remove pin from front mounting bracket. Remove cuffs from loader subframe by loosening nut and removing pin. (Figure 2-2) Figure 2-2 Drive In Close Enough To Allow Connecting Hydraulic Hoses To Tractor Outlets Front Bracket Cuff Removed 10 WARNING USE CAUTION WHEN MOUNTING LOADERS EQUIPPED WITH OPTIONAL CONTROL VALVE ON TRACTORS EQUIPPED WITH CANOPY. RAISING LOADER SUBFRAME TOO HIGH CAN PINCH HAND BETWEEN CONTROL HANDLE AND CANOPY CAUSING INJURY. D. With tractor at idle speed, ca...
Эта инструкция также подходит к моделям:Погрузчики - 2427 (1.37 mb)
Погрузчики - 3227 QT (1.37 mb)