Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
WARNING! For multiple spear Models GLB-3000, GLB-330, GLB-340, always insert spears into the bale – NEVER under the bale. Failure to insert spears into bale can allow bale to roll back when loader is raised, causing serious injury or death. Always use a tractor and front loader large enough to safely handle your bales. Check your tractor and front loader to make sure they are in good working condition. Check all loader mounting bolts to make sure they are tight. Check the tractor’s hydraulic system. Be sure the hydraulic oil and filter have been serviced according to manufacturer’s recommendations. Refer to your tractor or loader operator’s manual or dealer for any adjustments necessary to put the hydraulic system in good working order. Be sure tires and rims are in good condition. Inflate tires to the proper recommended air pressure. CAUTION! Be sure your tractor and loader is in good condition. Read all the safety precautions and make sure all equipment operators are familiar with the safety rules of operation. WARNING! ¦ Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS systems in “locked up” position at all times. ¦ Do not exceed the maximum recommended bale weight listed for each of the loader spear models. Damage to the equipment or serious personal injury could result. ¦ A heavy load can cause instability in driving a tractor. Make sure the rear of the tractor is properly counter-balanced with weights. Always drive slowly – especially around turns. An unstable tractor could steer badly and possibly tip over, causing injury or death. 14 INSTRUCTIONS (continued) ASSEMBLY —————————————————— Refer to the “exploded views” on pages 19-23 of this manual. Carefully follow instructions for final assembly. Remove the bucket from your front end loader. Check your loader to make sure it is in good working order. Check all frame mounting bolts to make sure they are tight. Place the main frame of the bale spear attachment on the universal euro tool carrier on the loader. Raise loader slightly and retract tilt cylinders until latch closes. NOTE: Latch automatically closes on global carrier. CAUTION! ALWAYS CHECK LATCH PINS BEFORE TILTING OR OPERATING ANY ATTACHMENT. Raise the loader and main frame slightly so that the bottom of the main frame is about two or three inches off the ground. Engage tractor parking brake and shut off the engine. Place some solid blocking under the main frame of the bale spear attachment for safety. A. On the Model GLB-2200, insert the long, forged main spear into the casting socket and align the cross hole in the spear with the hole in the socket. Install the 1/2” x 3” bolt and tighten the nut. Place the two short stabilizer spears into the sockets on the bottom of the main frame. Secure with the 5/16”x 13/4” bolts provided. B. On the Models GLB-3000, GLB-330, and GLB-340, install the long, forged main spears into the casting sockets in the main frame and align the cross hole in the spear with the hole in the socket. Install the 1/2”x 3” bolt and tighten the nut on each spear. OPERATION —————————————————— The operator is responsible for the safe operation of this equipment. The operator must be properly trained. Operators should be familiar with the attachment, tractor, and loader and all safety practices before starting operation. Make sure all operators have read the Owner’s/Operator’s Manual and are familiar with the instructions and the safety rules of operation. Be sure tractor is properly counter-balanced with weights before attempting to lift any load with the Bale Spear attachment. If you are handling bales with both the front end loader and the 3 pt. hitch on the tractor, always load the 3 pt. attachment first and unload last. The bale spear is to be used only for handling hay bales. Do not use for digging rocks, pulling out fence, or as a craning device with a chain over the spear. LARGE ROUND BALES: Using the bucket tilt cylinders, adjust the angle of the spear(s) so they are parallel with the center of the hay bale. With the tractor, push the spear(s) into the large hay bale. Make sure you have penetrated the hay bale far enough so the bale doesn’t want to come off the end of the spear(s). If, when you initially pick the bale up, it tends to droop forward, this would indicate you have not penetrated the bale far enough. Tilt the ends of the spear(s) upward (about 15-20 degrees) when transporting the hay bales. This will reduce any tendency for the bale to slide off the spear(s) while being transported. When you have placed the hay bale in the desired location, it is recommended to tilt the spear ends slightly downward (5-7 degrees) so as you pull away from the bale it will slide off the spear(s) more easily. Different location and circumstances will determine the best withdraw angle to use. NOTE: Always make sure bale spear fully penet...
Эта инструкция также подходит к моделям:Погрузчики - GLB-2200 (601.21 kb)
Погрузчики - GLB-3000 (601.21 kb)
Погрузчики - GLB-340 (601.21 kb)