Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
60179 U.S.A. PRINTED IN U.S.A. RULES FOR SAFE OPERATIONS Remember, any power equipment can cause injury if operated improperly or if the user does not und_ "stand how ta operate the equipment. I .IL. IMPORTANT SAFETY PRECAUTIONS. IT MEANS --ATTENTION. BECOME ALERT, YOUR I _1_ LOOK FOR THIS SYMBOL TO POINT OUT I I SAFETY IS INVOLVED. Exercise caution at all times, when using power equipment. 1. Read the tractor and dozer blade owners manuals and know how to operate your tractor,before using tractor with the dozer blade attachment. 2. Never operate tractor and dozer blade without wearing proper clothing suited to weather conditionsand operation of controls. 3. Never allow children to operate tractor and dozer blade, and do not allow adults to operate withoutproper instructions. 4. Always begin with transmission in first (low) gear and gradually increase speed as required. 48" DOZER BLADE CARTON CONTENTS (Also See Page 3) While confirming parts count, we suggest that you clear any paint from the 1/8" pin holes in part reference numbers 2, 3 and 4 to make assembly easier, REF NO. 1 2 3 4 5 6 7 QTY. (1) (1) (1) DESCRIPTION Blade Assembly Channel/Pivot Plate Assembly LiftAssembly Guide Bracket Assembly Blade Pivot Bracket Frame Bracket (RH) Frame Bracket (LH) CARTON CONTENTS REF. QTY. NO. 8 (2) 9 (1) 10 (1) 11 (2) 12 (1) 13 (1) 14 (2) (1) DESCRIPTION Lift Pivot Plate Support Bracket Handle Assembly w/grip Angle Lock Bars Grip Assembly Control Cable Assembly Spring Assembly Parts Package (Shown on Page 3) 2 CONTENTS OF PARTS PACKAGE (Figure 1) A B C D E F 1 ( _ d _ Stop Angle Keeper Plate LiftArm Link Spdng Pin 1/4 x 1" Cable Mount Bracket Nylon tie I G H I J K _i! , , (I0) / Cable Fitting, End Angle Lock Spring Shoulder Bolt Hex Whizlock Nut 3/8-16 Thread Hairpin Cotter 1/8" L M N 0 P 111)1HexBolt5116-18x1-112" Hex Lock Nut 5/16-18 Thread Hex Bolt 112-13 x 2-3/4" 2) Lock Washer 1/2" 2) Hex Nut 1/2-13 Thread QR 2/ Carriage Bolt 3/8-16 x 1-1/4" Lock Washer 3/8" T U Hex Bolt 3/8-16 x 1-1/4" Rat Washer 3/8" Std. V W X Y Z A.A AB AC A[_ i_)I 11 Pivot Bushing (short) Hex Bolt 1/4-20 x 1-1/4 ° Spacer (long) I-rexLock Nut 1/4-20 Thread Hex Bolt 1/4-20 x 5/8" Hex Bolt 3/8-16 x 1" Hex Jam Nut 5/16-24 Thread Clevis Pin 3/8" Dia. x 3/4" Lg. Hairpin Cotter 5/32" AEAF AE AFt i! I 2) Handle Guide Hex Bolt 1/2-13 x 4" Lg. Hex Jam Nut 1/2-13 Rat Washer 7116" Std. FIGURE 1 CARRIAGE AIAJ , AK !} Lift Rod Trunnion Hex Nut 3/8-16 Thread Hex Bolt 3/8-18 x 3/4" Lg. .., ... Q 318' SHOULDER 1/4" LOCK NUT 3/8 x 3/4• 1/4'.1-1/4" A__ N,%5116. JAMNUT 5_16 x a 1-1/_'__ 3/8' _ _x 1' 0 318x1"114" %_#_ l ( l 3/8x1-1/4" l _ / L] 3/8" WHIZLOCK © NUT ------' _'_'_ S 3/8" STD M 1/2" LOCK p 5/16' LOCKNUT 3/8" LOCKNUT © 1/2 X 4" I_'JAM NUT 7/16" STD I_tlt I €:I7P IAnl3_lAnr I-I::rl::n:-_lpr _[IA_ T 3/8" X 1-1/4" ASSEMBLY INSTRUCTIONS _-,,---'---'3/8" HEX NUT CARRIAGE BOLT 3_"LOCK TOOLS REQUIRED FOR ASSEMBLY (TOP HOLE WASHER 1) 7/1 6" Open End or Box Wrench _1) 1/2" Open End or Box Wrench (1) 9/16" Open End or Box Wrench (1) 3/4" Open End or Box Wrench ANGLE (1) Adjustable Wrench (1) Hammer FRONT Refer to carton contents figure on page 2 and figure 1 on page 3 for parts and hardware needed to assemble dozer blade. SLOT SPRING PIN RIGHT HAND (R.H.) AND LEFT HAND HOLE (L.H.) ARE DETERMINED FROM ANGLE LOCK OPERATOR'S POSITION WHILE CHANNEUPIVOT SPRING PLATE ASSEMBLY SEATED ON TRACTOR. FIGURE 3 1. Assemble curved end of angle lock spring into 3. Assemble the offset end of angle lock spring into small hole in washer as shown in figure 2. small holes in angle lock bars as shown in figure 3. Slide lock bars through lock bar slot until spring pin hole is aligned with bracket on back side. See figure 4. Using a hammer drive 1/4 =x 1=spring pin into lock bars until flush with bracket. See figure I T 4. Tighten nut in angle lock bars which was left loose in step 2. LO . POSITION \ \\ I ANGLE LOCK SPRING . F G--ffffiT 114-x 1" \ SPRING PIN _ '_ 2. Assemble the two angle lock bars together as FIGURE 4 shown in figure 3, using one 3/8" x 1-1/4" carriage bolt down through the top holes with a 3/8" lock rs_ NOTE washer and a 3/8" hex nut underneath. Do not Lock ba pivot freely and when tighten at this time. pulled all the way back the channel/pivot plate assembly should be unlocked and free to pivot to right or left position notches. 4 4. Assemble angle stop to top of channel using one 7. Assemble ball end of cable through round hole in 1/4" x 5/8" hex bolt down through left hand hole, cable end fitting and into slot of fitting. See and one 1/4" hex lock nut under channel. See figures 7 and 8. figure 5. Do not tighten at this time, 1/4" X 1-1/4" HEX BOLT I_"HEX LOCK NUT CHANNEWPIVOT PLATE _BLY CABLE END LONG SPACER FITTING ANGLE STOP PUSH 1/4" X 5/8" HEX BOLT ANGLE STOP FIGURE-5 5. Assemble 3/8" x 1-1/4" carriage bolt through square 1_" HEX LOCK NUT hole in cable mount bracket and through square hole in lock bars. See figures 6 and 7. Hold cable FIGURE 8 mount bracket...