Оценок - 4, средний балл: 4.8
(
)
)
|
Фрагмент инструкции
The remote temperature sensor (TX6U) and mounting bracket (Figure 2) 3. (3) 1/2" Philips screws 4. One strip of double sided adhesive tape 5. Instruction Manual and Warranty Card 6. (2) AAA 1.5V batteries 7. (2) AAA 1.5V batteries ADDITIONAL EQUIPMENT 1. Philips screwdriver (not included) Figure 1 Figure 2 2 QUICK SETUP Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries. 1. Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart. 2. Batteries should be out of both units for 10 minutes. 3. Place the batteries into the remote temperature sensor first then into the indoor temperature station. (All remote temperature sensors must be started before the indoor temperature station) 4. DO NOT PRESS ANY BUTTONS FOR 10 MINUTES. In this time the indoor temperature station and remote temperature sensor will start to talk to each other and the display will show both the indoor and outdoor temperature. If the indoor temperature station does not display both temperatures after the 10 minutes please retry the set up as stated above. After both the indoor and outdoor temperatures are displayed for 10 minutes you can place your remote temperature sensor outdoors and set the time. The remote temperature sensor has a range of 80 feet and should be placed in a dry, shaded area. 3 Any walls the signal will have to pass through will reduce distance. An outdoor wall or window will have 20 to 30 feet of resistance and an interior wall will have 10 to 20 feet of resistance. Your distance plus resistance should not exceed 80 feet in a straight line. NOTE: Fog and mist will not harm your remote temperature sensor, but direct rain must be avoided. To complete the setup of your indoor temperature station after the 10 minutes have passed, please follow the steps below: 1. To set the time, press and hold the "SET" button for 5 seconds. Note: A "12h" or "24h" will appear on the top line. ("12h" for AM/PM, "24h" for military time) a. To change between "12h" and "24h" press and release the "MIN/MAX" button. b. When you have your choice shown on the display press and release the "SET" button once. 2. Degrees Fahrenheit will now show. a. To change between Fahrenheit and Celsius, press and release the "MIN/MAX" button. b. When you have your choice shown on the display press and release the "SET" button once. 4 3. The hour will now be flashing. a. Press and release the "MIN/MAX" button until the correct hour is shown. Note: When in the 12h mode "PM" is displayed under the word "TIME" during PM hours. During the AM hours this area will be blank. b. When the correct hour is shown, press and release the "SET" button once. 4. The minutes will now be flashing. a. Press and release the "MIN/MAX" button until the correct minutes are displayed. Press and release the SET button once more to complete the setup. DETAILED SETUP GUIDE I. BATTERY INSTALLATION A. REMOTE TEMPERATURE SENSOR 1. Remove the mounting bracket. 2. Remove the battery cover. 3. Observing the correct polarity, install (2) AA batteries—make sure they do not spring free, or start-up problems may occur. Replace the cover. 5 B. INDOOR TEMPERATURE STATION Note: After the batteries are installed, DO NOT press any buttons. This may interfere with the signals, causing temperatures to register incorrectly. Battery Cover 1. Remove the battery cover on the backside. To do this, push the cover upward and pull it out. 2. Observing the correct polarity, install (2) AAA batteries. 3. Replace the battery cover. 4. Wait 10 minutes or until both the indoor and outdoor temperatures are shown on the indoor temperature station. 6 5. The indoor temperature station should now show: "-:- -" in the TIME LCD, and temperatures in the INDOOR and OUTDOOR LCD’s. II. TIME A. SETTING THE TIME 1. Press and hold the "SET" button for 5 seconds, "12h" will appear in the TIME LCD. 2. Press and release the "MIN/MAX" button to select either 12h time (am/pm) or 24h time. 3. Press and release the "SET" button 2 times, the hour will flash in the upper left corner. 7 4. Press and release the "MIN/MAX" button to set the hour. 5. Press and release the "SET" button to move to the minute setting. 6. Press and release the "MIN/MAX" button to set the minutes. 7. Press and release the "SET" button to activate the clock. Note: When in 12h mode, there is only a "PM" display, which appears under "TIME." If there is no display, then it is in AM mode. Make sure you set the time accordingly. III. UNITS OF TEMPERATURE MEASURE A. SELECTING UNITS OF MEASUREMENT 1. Press and hold the "SET" button for 5 seconds until "12h" or "24h" appears in the TIME LCD. 2. Press and release the "SET" button again, "°F" will appear in the TIME LCD. 3. Press and release the "MIN/MAX" button to shift between °F and °C. 4. Press and release the "SET" button twice to activate settings. 8 IV. FEATURES A. MINIMUM AND MAXIMUM TEMPERATURES 1. Press and release the "MIN/MAX" button. "MIN" appears in the temperature LCDs...
Эта инструкция также подходит к моделям:Погодные станции - WS-7013U (124.83 kb)