Войти:
Оценок - 2, средний балл: 4 ( )

Инструкция по эксплуатации Honeywell, модель TS13C

Производитель: Honeywell
Размер: 49.2 kb
Название файла: 5b79068b-36a4-4e7c-8040-88e86ec4e1c8.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


• Install 2 “ AA” size alkaline batteries (not included) matching the polarities shown in the battery compartment. • Replace the battery compartment door and secure the screws. • Secure remote sensor in the desired location. LOW BATTERY WARNING A low-battery indicator [ ] will appear on the remote temperature reading line of the main unit, warning that the remote sensor batteries need replacement. PLACEMENT OF THE REMOTE SENSOR The remote sensor can be mounted on the wall using the recessed screw hole or placed on a flat surface indoors or outdoors. 7 GETTING STARTED After batteries are installed; remote sensor will transmit temperature readings at 45 second intervals. The main unit may take up to two minutes to receive the initial readings. Upon successful reception, remote temperature will appear on the main unit’s display. The main unit will automatically update readings at 45-second intervals. LOST COMMUNICATION If the main unit display line for the remote sensor reading goes blank, refer to the main unit’s User Manual to find out the way to begin a new signal search. If the signal still isn’t received, please make sure that: • The remote sensor is in its proper location. • The distance between main unit and remote sensor is not over 100 feet (30meters). • The path between units is clear of obstacles. Shorten the distance if necessary. • Fresh batteries are installed correctly in both remote sensor and main unit. If there is no reception, please perform the following steps: • Bring the main unit and remote sensor close together. • Remove four (4) small screws from the back of the remote sensor with small Phillips screwdriver, and open the battery compartment. • Remove the batteries from the battery compartment and reinstall them in the same manner. Remote sensor LED indicator will flash showing transmission of the signal. 8 7 • Remove the batteries from the main unit and reinstall them in the same manner. • The remote temperature appeared on the main unit’s display will show that transmission is being received successfully. TRANSMISSION COLLISION Signals from the other household devices such as wireless doorbells, home security systems, and entry control, may interfere with this product or cause temporary reception interruption. This is normal and will not affect the general performance of the product. The transmission and reception of the temperature readings will resume once the interference subsides. PRECAUTIONS This product is engineered to give you years of satisfactory service if handled carefully. Here are a few precautions: • Do not immerse the unit in water. • Do not clean the unit with abrasive or corrosive materials. They may scratch the plastic parts and corrode the electronic circuits. • Do not subject the product to excessive force, shock, dust, temperature, or humidity, which may result in malfunctions, shorter lifespan, damaged batteries, and damaged parts. • Do not tamper with the unit’s internal components. Doing so will invalidate the warranty and may cause damage. This unit contains no user-serviceable parts. • Use only fresh batteries. Do not mix new and old batteries. • Read the user's manual thoroughly before operating the unit. 9 SPECIFICATIONS Remote TemperatureProposed operating range with alkaline batteries: -20.0°C to + 70.0°C/-4.0°F to + 158°F Proposed operating range with lithium batteries: -38.8°C to + 70.0°C/-38.0°F to +158°F Temperature resolution: 0.1°C/0.2°FLCD display of registered temperature Low battery indicator RF Transmission Frequency: 433 MHz Maximum number of transmission channels: three (3) RF transmission range: Maximum 100 feet (30 meters) Temperature transmission cycle: approximately 45 seconds Wall Mount or Desktop option Power 2 AA size (UM-3) 1.5V batteries (not included) Dimensions 2.37(L) x 4(H) x 1(D) inch 10 9 FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modification to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment had been tested and found to comply with the limits for a Class B Digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment, installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to improve or correct turning the interference by one or more o...


Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории