Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Indoor/Outdoor temperature indicator 3. Battery indicator 4. Time/temperature display 5. Time zone indicator 6. AM/PM indicator 7. Clock signal reception indicator BACK VIEW 2 1 1. Adaptor socket 2. Indoor temperature sensor BOTTOM VIEW 1 2 7 6 5 3 4 1. CLOCK: Set time and display mode 2. / : Increase / decrease setting; activate / deactivate clock reception signal 3. AUTO ON / OFF: Select auto toggle mode 4. °C / °F: Select temperature unit and display mode 5. Battery compartment 6. EU / UK: Select the nearest radio signal (BAR1000 only) 7. RESET: Reset unit to default settings REMOTE SENSOR 1 2 3 4 5 RESET 1 2 3 1. LED status indicator 2. Wall mount hole 3. Battery compartment 4. RESET hole 5. CHANNEL switch GETTING STARTED POWER SUPPLY Batteries serve as back up power supply for the clock. For continuous use, always plug in the adaptor socket. Make sure it is not obstructed and is easily accessible to the unit. To completely disconnect from power, the adaptor should be disconnected from the main unit. NOTE The main unit and adaptor should not be exposed to wet conditions. No objects filled with liquid, such as vases, should be placed on the main unit and adaptor. To insert batteries: 1. Use a screwdriver to remove the battery compartment and insert the batteries, matching the polarities. 2. Press RESET after each battery change. NOTE Batteries should not be exposed to excessive heat such as sunshine or fire. indicates main unit batteries are low. REMOTE SENSOR To set up the outside sensor: 1. Open the battery compartment. 2. Insert the battery, matching the polarities. 3. Select a channel then press RESET. 4. Close the battery door. 5. Place the outside sensor within 30 m (98 ft) of the main unit using the table stand or wall mount. TIP The transmission range may vary depending on many factors. You may need to experiment with various locations to get the best results. NOTE Use alkaline batteries for longer usage and consumer grade lithium batteries in temperatures below freezing. SENSOR DATA TRANSMISSION The main unit will automatically search for the outdoor sensor. The sensor reception icon in the remote sensor area shows the status: ICON DESCRIPTION Main unit is searching for sensor. A channel has been found. The sensor cannot be found. NOTE If the sensor is not found, check the batteries, obstructions and remote sensor location. For best results: • Place the sensor out of direct sunlight and rain. • Position the sensor facing the main unit, minimizing obstructions. • Place the sensor in a location away from metallic or electronic objects. • Position the sensor close to the main unit during cold winter months. CLOCK CLOCK RECEPTION This product is designed to synchronize its clock automatically with a clock signal. BAR1000: • EU: DCF-77 signal: within 1500 km (932 miles) of Frankfurt, Germany. • UK: MSF-60 signal: within 1500 km (932 miles) of Anthorn, England. BAR1000A: • WWVB-60 signal: within 3200km (2000 miles) of Fort Collins Colorado. To enable / disable signal reception: Press and hold to enable or to disable signal reception. NOTE Reception takes 2-10 minutes. If the signal is weak, it can take up to 24 hours to get a valid signal. Clock signal reception indicator: STRONG SIGNAL WEAK/NO SIGNAL SET CLOCK To set the clock manually, disable the signal reception first. 1. Press and hold CLOCK. 2. Press or to change the settings. 3. Press CLOCK to confirm. 4. The settings order is: time zone offset, 12/24 hr format (BAR1000 only), hour and minute. BAR1000: Time zone offset sets the clock +/- 23 hours from the received clock signal time. If you have deactivated the clock signal reception, do not set a value for time zone offset. BAR1000A: Select the time zone: (0) Pacific, (+1) Mountain, (+2) Central or (+3) Eastern. CHANGE DISPLAY • To change to auto toggle mode (clock > outdoor temperature > indoor temperature), slide AUTO ON / OFF to ON. • To manually toggle between time, outdoor temperature and indoor temperature, press CLOCK or wave your hand at least 1.5 inches or less from the motion sensor located on the top of the main unit. NOTE Auto toggle mode and motion sensor will be disabled if a button is pressed, but will be enabled again if no button is pressed for 5 seconds. NOTE The installed CDS light sensor inside the unit will activate automatic LCD dimming. WEATHER FORECAST This product forecasts the nex t 12 to 24 hours of weather. ICON COLOR Red Blue Green MEANING Sunny Cloudy Rainy TEMPERATURE To display temperature mode or select temperature unit: Press °C / °F. NOTE Please keep the temperature sensor (adjacent to the adaptor socket) away from electrical devices as heat from these devices will affect accurate indoor temperature readings. RESET Press RESET to return to the default settings. PRECAUTIONS • Do not subject the unit to excessive force, shock, dust, temperature or humidity. • Do not cover the ventilation hole with any items such as newspapers, curtains etc. • Do not immerse the ...