Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
Glass is breakable. • Avoid striking, scratching or slamming glass • Avoid abrasive cleaners • Do not clean glass while it is hot E. Firebrick Inspection • Frequency: After each ash removal • By: Homeowner Replace the firebrick if they become, cracked, broken, crumbly and/or if there is a 1/4 inch (6.35mm) gap between the bricks. The firebox is lined with high quality firebrick, which has exceptional insulating properties. There is no need to use a grate; simply build a fire on the firebox floor. Do not operate appliance without firebrick. 1. After the coals have completely cooled, remove all old brick and ash from unit and vacuum firebox. 2. Remove new brick set from box and lay out to diagram shown. 3. Lay bottom bricks in unit. 4. Install rear bricks on the top of the bottom bricks. Slide top of bricks under clip on back of firebox wall and push bottom of brick back. 5. Install side bricks. Slide top of brick under clips on side of firebox and push the bottom of the brick until it is flush with the side of the unit. Use Part 832-0550 when ordering individual brick. Provide brick dimension or copy this page, mark the desired brick and take it to your authorized dealer. Figure 18.1 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 No. Brick Size Qty 1 9 x 4-1/2 x 1-1/4 20 2 9 x 2-1/4 x 1-1/4 4 Heatilator • ECO-ADV-WS22 • 7057-128D • September 15, 2011 Heatilator • ECO-ADV-WS22 • 7057-128D • September 15, 2011 19 Baffle Blanket Latch Cam Spacing Washers Baffl e & Blanket Optional Blower Chimney System Firebrick & Ash Removal Door & Glass Assemblies Door Handle Frequency MONTHLY or After Every Cord of Wood Baffl e and blanket placement is critical to heat output, effi ciency and overall life of the unit. Make sure the baffl e is pushed all of the way to the back of the fi rebox and the blanket is laying fl at. Inspect baffl e for cracks. YEARLY or After Every 4 Cords of Wood Vacuum the blower impellers. EVERY 2 MONTHS or After Every 4 Cords of Wood The chimney and chimney cap must be inspected for soot and creosote ever two months during the burn season or more frequency if chimney exceeds or is under 14-16 ft (4.3m- 4.8m) measured from bottom of appliance. This will prevent pipe blockage, poor draft, and chimney fi res. Always burn dry wood to help prevent cap blockage and creosote build-up. WEEKLY or After Every 25 Loads of Wood Ashes must be cool and then you can dispose of the ashes in a non-combustible container. Firebrick is designed to protect your fi rebox. After ashes are removed, inspect the fi rebrick and replace fi rebricks that are crumbling, cracked or broken. WEEKLY or After Every 25 Loads of Wood Keep door and glass gasket in good shape to maintain good burn times on a low burn setting. To test: place a dollar bill between the stove and door and then shut the door. If you can pull the dollar out, remove one washer from door handle behind latch cam and try again. If you can still pull it out, replace the door gasket. Check the glass frame for loose screws to prevent air leakage. Check glass for cracks. WEEKLY or After Every 25 Loads of Wood Check the door latch for proper adjustment. This is very important especially after the door rope has formed to the stove face. Check door handle for smooth cam operation. Task CAUTION! Allow the appliance to completely cool down before performing any cleaning or maintenance. Start the fi rst inspection after the fi rst 2 months of use, or if performance changes, and adjust your schedule accordingly. Maintenance is required for safe operation and must be performed to maintain your warranty. F. Quick Reference Maintenance Guide 4 Troubleshooting Guide With proper installation, operation, and maintenance your woodstove will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist you or a qualified service person in the diagnosis of a problem and the corrective action to be taken. Start Fire Problems Can not get fi re started Excessive smoke or spillage Burns too slowly Not enough heat output Fire burns too fast Possible Cause Not enough kindling/paper or no kindling/paper Not enough air for fire to ignite Wood condition is too wet, too large Bed of coals not established before adding wood Flue blockage such as birds’ nests or leaves in termination cap Down draft or negative pressure Competition with exhaust devices Extremely dry or soft wood Overdrafting Solution Use dry kindling, more paper. Arrange kindling & wood for air movement. Check for restricted termination cap Check for blockage of outside air kit (if installed). Check for fl ue blockage. Pre-warm flue before starting fire (refer to Building a Fire Section). Check for adequate vent height (refer to Chimney Height Section). Open window below the appliance towards the wind. Use dry, seasoned wood (refer to Seasoned Wood Section). Start with paper & kindling to establish bed of coals (refer to Building a Fire Section). Have chimney inspected for creos...
Эта инструкция также подходит к моделям:Плиты - ECOCHOICE ECO-ADV-WS22 (1.68 mb)
Плиты - ECOCHOICE ECO-ADV-WS22 (1.68 mb)
Плиты - ECOCHOICE ECO-ADV-WS22 (1.68 mb)