Оценок - 5, средний балл: 3.6
(
)
)
|
Фрагмент инструкции
1. Press keys 2 and 3 at the same time. The programmer starts to work. ON SWITCHING ON FOR THE FIRST TIME OR AFTER A BLACK-OUT SETTING THE TIME 2 3 IIIIII II I I II IIIIIIIIII II I I II IIII A U T O 2 3 5 6 IIII II I I II I The programmer has an electronic clock (12 hours) with luminous figures which indicate hours and minutes. Note: Setting the clock will zero any programmes in progress or set. 1. Press pushbuttons 2 and 3 at the same time. 2. Press pushbuttons 5 or 6 until the exact time is set. During this phase the dot between hours and minutes will flash on the display. If the plus or minus keys are kept pressed for a few seconds, the figures will scroll more quickly. P on the display indicates PM time. AUDIBLE SIGNAL The intermittent audible signal, duration 30 seconds, sounds when the timer or semiautomatic or automatic cooking have reached the end of the time set. It also sounds to signal that the door is open (see oven use chapters). To silence the audible signal press any of the programmer keys TIMER I II I I III II I The timer function is only used to count the time and does not influence oven operation or any programmes which are in progress or set. 1. Press pushbutton 1. The bell symbol will start to flash. 2. Press keys 5 or 6 to set the time required. 3. The countdown starts immediately. The bell symbol stops flashing and the time appears again. 4. To see the countdown press pushbutton 1. The time will be indicated in hours and minutes; the seconds are only indicated for the last minute. 5. At the end of the countdown an audible signal sounds and the bell symbol on the display flashes. Press any pushbutton to stop the audible signal. IMPORTANT WARNING: This function is only an electronic alarm and does not switch OFF the oven. Remember to turn OFF manually the selector knob at the end of the countdown. SEMI-AUTOMATIC COOKING 1 5 6 Start immediate cooking and switch the oven off automatically after the programmed cooking time. Setting 1. Set the cooking function by turning the oven selector to the function required. 2. The cooking temperature appears on the display. To change it proceed as described in the Setting the cooking chapter 3. Press pushbutton 2. AUTO starts to flash and 0.00 appears. 4. Press pushbuttons 5 or 6 to set the cooking time (cooking time in hours and minutes: set it to ten minutes less than the time required because the stored heat will complete the cooking). 5. On the display AUTO becomes steady and the cooking programme starts. During cooking 6. During the cooking cycle, the display shows the oven temperature measured by the probe or pre-setted temperature. Press key 2 to display the time remaining until the end of cooking. The cooking time and temperature can be varied at any time, as described above. At the end of cooking 7. End appears on the display, AUTO flashes and the audible signal sounds. The cooking cycle has finished and the oven is OFF. 8. Press any programmer pushbutton to stop the audible signal. 9. OFF appears (oven OFF). 10. Turn the function selector to OFF (oven OFF). 11. The programmer display shows the time. 2 5 6 I III I I I II I I I I I II I I II I I I I III I I I II I I Note: At the end of the programme always turn the function selector knob to OFF (oven OFF). AUTOMATIC COOKING 2 5 6 I III I I I II I I I I I II I I II I I I I 3 5 6 I III I I I II I I III I I I II I Start cooking at the programmed time and switch the oven off automatically after the programmed cooking time. Setting 1. Set the cooking function by turning the oven selector to the function required. 2. The cooking temperature appears on the display. To change it proceed as described in the Setting the cooking chapter. 3. Press pushbutton 2. AUTO starts to flash and 0.00 appears. 4. Press pushbuttons 5 or 6 to set the cooking time (cooking time in hours and minutes: set it to ten minutes less than the time required because the stored heat will complete the cooking). 5. On the display AUTO becomes steady and the cooking programme starts. 6. Press pushbutton 3 (AUTO starts to flash). 7. Press pushbuttons 5 or 6 to set the time when the cooking should finish. The values set must be correct; e.g. if it is 08:00 a cooking time of 3 hours, ending at 10:00, cannot be set. In this case the programmer automatically sets the end of cooking time for 11:00. 8. On the display AUTO becomes steady and the time appears again. The cooking symbol goes out. Starting cooking 9. The pan symbol lights up. The oven switches on and the cooking cycle set starts. During cooking 10. During the cooking cycle, the display shows the oven temperature measured by the probe or pre-setted temperature. Press key 2 to display the length of cooking set. Press key 3 to display when the cooking will finish. The cooking time, end of cooking time and cooking temperature can be varied at any time, as described above. At the end of cooking 11. End appears on the display, AUTO flashes and the audible signal sounds. The cooking c...