Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Correct flame formation Burner The flame formation and temperature development must be checked for each burner after the appliance is converted to a different gas type. In the event of a problem, compare the nozzle values to the values in the table. Only for models without safety pilot 1. Ignite the hob burner as described in the operating instructions. 2. Check the large and small flames for the correct flame formation. The flame must burn evenly and continuously. 3. Using the burner knob, switch quickly between the large and small frame. Repeat this process a few times. The gas flame must not flicker or go out. Only for models with safety pilot 1. Ignite the hob burner as described in the operating instructions. 2. Turn the burner knob to the small flame setting. Check whether the ignition is activated by holding the knob in the " small flame" position for approximately 1 minute. 3. Check the large and small flames for the correct flame formation. The flame must burn evenly and continuously. 4. Using the burner knob, switch quickly between the large and small frame. Repeat this process a few times. The gas flame must not flicker or go out. Oven Lower gas burner or grill burner ( optional) 1. Ignite the lower gas burner as described in the operating instructions. 2. Check the flame formation with the oven door open: The flame must burn evenly throughout (it may be slightly uneven in the first few minutes, but after a few minutes, the flames should burn constantly) . 3. To check that the thermocouple is functioning correctly, let the appliance run for a few minutes. If necessary, check the settings. If it is not functioning correctly, replace the bypass screw in the burner. Technical properties - gas Here, you will find a list of the different gas types and corresponding values. Nozzle values for the auxiliary burner *G20/ G20 G20 G25 G25 G30 * *G30 GZ35 G25.1 GZ41 GZ50 GPB G25 Gas pressure (mbar) 20/ 25 20 25 20 25 28-30 50 13 25 20 20 36 Nozzle (mm) 0,72 0,72 0,68 0,77 0,72 0,50 0,43 1,06 0,72 0,77 0,72 0,47 Bypass screw (mm) 0,50 0,50 0,50 0,50 0,50 0,30 0,30 0,67 0,50 0,50 0,50 0,30 Max. input power (kW) 1 1 1 1 1 1 1 1 1 1 1 1 Max. input power ( kW) . 0.55 . 0.55 . 0.55 . 0.55 . 0.55 . 0.55 . 0.55 . 0.55 . 0.55 . 0.55 . 0.55 . 0.55 Gas discharge for 15 °C and 0,095/ 0,095 0,11 0,111 0,111 - - 0,139 0,111 0,120 0,1 - 1,013 mbar m ./ h 0,111 Gas discharge for 15 °C and - - - - - 73 73 - - - - 74 1,013 mbar g/ h * For France and Belgium ** For G30 (50 mbar), the nozzle set HEZ298070 must be ordered from the service centre. Nozzle values for the standard burner *G20/ G20 G20 G25 G25 G30 * *G30 GZ35 G25.1 GZ41 GZ50 GPB G25 Gas pressure (mbar) 20/ 25 20 25 20 25 28-30 50 13 25 20 20 36 Nozzle (mm) 0,97 0,97 0,91 1 0,94 0,65 0,58 1,31 0,94 1,00 0,97 0,62 Bypass screw (mm) 0,58 0,58 0,58 0,58 0,58 0,38 0,38 0,75 0,58 0,58 0,58 0,38 Max. input power (kW) 1,75 1,75 1,75 1,75 1,75 1,75 1,75 1,75 1,75 1,75 1,75 1,75 Max. input power ( kW) . 0.9 . 0.9 . ...
Эта инструкция также подходит к моделям:Плиты - HGG933150J/02 (945.15 kb)
Плиты - HGG933150J/03 (945.15 kb)
Плиты - HGG933150J/04 (945.15 kb)
Плиты - HGG933150J/05 (945.15 kb)