Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
WARNING: Make sure the selector switch is in the OFF position when you are away from home for long periods of time. Heater will come on automatically with selector switch in the ON position. Pilot Burner Ignitor Electrode Figure 25 - Pilot No Control Options) 14 104461 Remote Selector Switch in Remote Position (Optional Remote Control) ON OFF REMOTE OFF PILOT ON LO IH ON OFF REMOTE OFF PILOT ON LO IH OWNER’S MANUAL OPERATING HEATER Continued TO TURN OFF GAS TO APPLIANCE Shutting Off Heater 1. Turn control knob clockwise to the OFF position. 2. Set selector switch in the OFF position to keep from draining battery. Shutting Off Burners Only (pilot stays lit) You may shut off the burners and keep the pilot lit by doing one of the following: 1. Turn control knob clockwise to the PILOT position. 2. Use remote control manual OFF button. 3. Set remote selector switch in the OFF position. MANUAL LIGHTING PROCEDURE 1. Follow steps 1 through 6 under Lighting Instructions, page 14. 2. Depress control knob and light pilot with match. 3. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow steps 9 through 11, page 14. OPTIONAL REMOTE OPERATION Note:All remote control accessories must be purchased separately (see Accessories, page 33). Follow instructions included with the remote control. Thermostat Control Operation (Optional GHRCTA Only) The thermostat control setting on the remote control unit can be set to any comfort level between WARMER and COOLER. The burners will turn on and off automatically to maintain the comfort level you select. The ideal comfort setting will vary by household depending upon the amount of space to be heated, the output of the central heating system, etc. Figure 26 - Setting the Remote Selector Switch, Control Knob, and Flame Adjustment Knob for Remote Operation Increases Room Temperature in AUTO Shows Temperature Mode Setting Decreases Room The Log Heater will Temperature in AUTO Automatically Cycle Mode between Pilot and the Heat Setting that has Turns Burners On or Off been Selected and Allows You to Choose the Auto Setting Figure 27 - Thermostat Hand-Held Remote Control Unit Selections (GHRCTA Series Only) Continued For wall thermostat operation, follow instruction supplied with thermostat accessory GWMT1. For wall switch operation follow instructions supplied with GWMS2. NOTICE: You must light the pilot before using the hand-held remote control unit. See Lighting Instructionson page 14. 1. After lighting, let pilot flame burn for about one minute. Turn control knob to ON position. Adjust flame adjustment knob anywhere between HI and LO. Slide the remote selector switch to the REMOTE position. Note:The burners may light if handheld remote ON button was on when remote selector switch was last turned off. You can now turn the burners on and off with the handheld remote control unit. IMPORTANT: Do not leave the remote selector switch in the REMOTE position when the pilot is not lit. This will drain the battery. IMPORTANT: Be sure to press the ON/OFF buttons on the hand held remote control unit for up to 3 seconds to assure proper operation. GHRC Series Operation: 2a. Press the ON/OFF button to turn the burners on and off. When turning burners off, the pilot will remain lit. GHRCTA Series Operation: 2b. Press the AUTO/ON/OFF button on the hand-held remote control (see Figure 27). The lights to the left of the button will show AUTO, ON, or OFF. • In the ON mode, the burners will ignite. The heater is in manual mode when ON is lit. Flame Adjustment Knob Control Knob in On Position 104461 15 DESA INTERNATIONALVENT-FREE NATURAL GAS STOVE HEATER OPERATING HEATER Continued • In the AUTO mode, the thermostat in the hand-held remote unit controls the room temperature. To increase the room temperature, press the top arrow of the TEMP button. To lower the room temperature, press the bottom arrow of the TEMP button. At higher settings the heater will run longer. IMPORTANT:This remote control has been specially engineered to take an air temperature sample every minute in the auto mode. It will not respond immediately to the temperature setting being turned up or down. IMPORTANT: The hand-held remote control unit must be near the heater. Do not keep the hand-held remote control unit too close to the heater. The thermostat on the hand-held remote control unit will heat up too quickly and turn the heater off. 3. To turn the burner off, press the AUTO/ON/OFF button until OFF lights. The pilot will remain lit. IMPORTANT: To turn the pilot off, manually turn the control knob on the heater to the OFF position. LIGHTING INSTRUCTIONS SVYD18N and FSVYD18N Manual-Variable Control Models NOTICE: During initial operation of new heater, burning logs will give off a paper-burning smell. Open damper or window to vent smell. This will only last a few hours. 1. STOP! Read the safety information page 14, column 1. 2. Make sure equipment shutoff valve is fully ...
Эта инструкция также подходит к моделям:Плиты - (F)SVYD18N (674.98 kb)