Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Important Notes Installation, and any demonstration, information or adjustments are not included in the warranty. The cooker must be installed by a suitably qualified and registered person in accordance with the relevant Standards. 24 24 Care and Maintenance Important: As a safety measure, before you start cleaning the cooker be sure to disconnect it from the mains supply. Do not use cleaning products with a chlorine or acidic base. Do not use a steam cleaner because the moisture can get into the appliance thus make it unsafe. The use of suitable protective clothing/gloves is recommended when handling or cleaning of this appliance. Warning When correctly installed, your product meets all safety requirements laid down for this type of product category. However special care should be taken around the rear or the underneath of the appliance as these areas are not designed or intended to be touched and may contain sharp or rough edges, that may cause injury. Flexible Tube From time to time, check the flexible tube connecting the gas supply to the cooker. It must be always in perfect condition; in case of damage arrange for it to be replaced by a suitably qualified and registered installer. Gas Taps If a tap becomes stiff, do not force; contact your Local Service Centre. Cleaning the Hob Spillage on the hob can usually be removed by a damp soapy cloth. More obstinate stains can be removed by rubbing gently with a soapy nylon (non metal) scouring pad or mild household cleaner. Enamelled Parts All the enamelled parts must be cleaned with a sponge and soapy water only or other non-abrasive products. Dry preferably with a micro fibre or soft cloth. 25 25 Stainless Steel, Aluminium, Painted Parts and Silk-Screen Printed Surfaces Clean using an appropriate product. Always dry thoroughly. Stainless steel surfaces: can be cleaned with an appropriate stainless steel cleaner. IMPORTANT: these parts must be cleaned very carefully to avoid scratching and abrasion. You are advised to use a soft cloth and neutral soap. CAUTION: Do not use abrasive substances or non-neutral detergents as these will irreparably damage the surface. Glass Control Panel Clean using an appropriate product. Always dry thoroughly. Do not use harsh abrasive cleaners or sharp metal scrapers to clean the control panel since they can scratch the surface, which may result in shattering of the glass. 26 26 F C Fig. 17 Fig. 16 Burners and Grids – These parts can be removed and cleaned with appropriate products. – After cleaning, the burners and their flame spreaders must be well dried and correctly replaced. – It is very important to check that the burner flame spreader and the cap have been correctly positioned. Failure to do so can cause serious problems. – Check that the electrode “S” (figs. 16-18) is always clean to ensure trouble-free sparking. – Check that the sensor “T” (figs. 16-18) next to each burner is always clean to ensure correct operation of the safety valves. – Both the sensor and ignition plug must be very carefully cleaned. – Note: To avoid damage to the electric ignition do not use it when the burners are not in place. Correct Positioning of the Burners (Auxiliary, Semi-Rapid and Rapid Burners) – It is very important to check that the burner flame spreader “F” and the cap “C” have been correctly positioned (see figs. 16 and 17). Failure to do so can cause serious problems. Ignitor “S” Sensor “T” 27 Correct Position of Triple Ring Burner The triple ring burner must be correctly positioned (see fig. 18); the burner ribs must be fitted in their housing as shown by the arrow. The burner correctly positioned must not rotate (fig. 19). Then position the cap “A“ and the ring “B“ (figs. 19 - 20) A B Fig. 19 Fig. 18 Fig. 20 Sensor “T” Ignitor “S” 28 28 Storage Compartment (Model RV 901 ..) – The storage compartment (fig. 21) is accessible through the pivoting panel. Attention: Do not store flammable material in the oven, or the storage compartment. Drawer (Model RV 1001 ..) The drawer (fig. 22) comes out like a normal drawer. Attention: Do not store flammable material in the ovens, or the drawer. Fig. 21 Fig. 22 mod. RV 901 .. mod. RV 1001 .. 29 Inside of Oven The oven should always be cleaned after use when it has cooled down. The cavity should be cleaned using a mild detergent solution and warm water. Suitable proprietary chemical cleaners may be used after first consulting with the manufacturers recommendations and testing a small sample of the oven cavity. Abrasive cleaning agents or scouring pads/cloths should not be used on the cavity surface. NOTE: The manufacturers of this appliance will accept no responsibility for damage caused by chemical or abrasive cleaning. Let the oven cool down and pay special attention no to touch the hot heating elements inside the oven cavity. Assembling and Dismantling of the Side Runner Frames – Fit the side runner frames into the holes on the side walls inside the oven (Fig. 23). – Slide the tray and rack int...
Эта инструкция также подходит к моделям:Плиты - RV 1001 (4.29 mb)