Оценок - 5, средний балл: 4.2
(
)
)
|
Фрагмент инструкции
.. Instructions for the user 10. Cleaning and maintenance Before cleaning or carrying out maintenance, switch off the power supply to the appliance and close the gas tap. Do not clean the surfaces of the appliance when they are still hot. 10.1 Cleaning stainless steel surfaces To clean and preserve the stainless steel surfaces and remove the toughest stains, always use specific products, provided they do not contain chlorine-based abrasives or acid substances, or a little warm vinegar. Pour the product onto a damp cloth and wipe the steel surface. Rinse carefully and dry with a soft cloth or a piece of deerskin. Do not under any circumstances use metallic sponges or sharp scrapers that may damagethe surfaces. Only use non-scratch, non-abrasive sponges and, if necessary, wooden or plastic utensils. 10.2 Cleaning enamelled surfaces Clean with a non-scratch, non-abrasive sponge dampened with soap and water. Grease stains can easily be eliminated with hot water or a product specifically made for cleaning enamel. Rinse carefully and dry with a soft cloth or a piece of deerskin. Do not use products containing abrasives, scouring pads, steel wool or acid, which mayspoil the surfaces. Do not leave acid or alkaline substances on the enamel (lemon juice, vinegar, salt, etc.). 10.3 Cleaning the knobs and the control panel Clean the knobs and the control panel with a damp cloth. 10.4 Cleaning the grids and burners To clean the grids and hob burners, remove them from their housing by lifting them upwards as shown in the figure, and immerse them in a solution of warm water and non-abrasive detergent for about ten minutes. Rinse and dry carefully. Always check that none of the burner openingsis clogged. Be sure to refit the burner correctly, checking the flame is uniform. We recommend carrying out this operation at least once a week and each time it is necessary. .. Instructions for the user 10.5 Cleaning the igniter plugs and thermocouples In order for the igniter plugs and thermocouples to operate correctly, they must be kept clean at all times. Check them frequently and, if necessary, clean them with a damp cloth. Any dry residue should be removed with a toothpick or needle, taking care not to damage the insulating ceramic part. 10.6 Cleaning the fry-top Any grease deposits on the fry-top can be eliminated more easily when the griddle is still warm. If necessary, leave it to cool and soak for a few minutes. Finally, clean with warm soapy water, dry with a tea cloth or kitchen roll. 10.7 Cleaning the ceramic hob The ceramic hob must be cleaned regularly, each time it is used if possible, when the latent heat lights are off. Any light-coloured marks caused by aluminium-based pans can be removed with a damp cloth dipped in vinegar. Any burnt residue left after cooking can be removed with a wooden spatula. Rinse with water and dry well with a clean cloth. Do not under any circumstances use abrasive or corrosive detergents (e.g. powder products, oven sprays, stain-removers or metallic sponges). The cooking surface of the ceramic hob is extremely resistant. It is not however unbreakable and may be damaged, above all by pointed or hard objects if dropped onto it with a certain force. Should the surface of the ceramic hob be broken, cracked or split, using it may cause electrocution! Call Customer Services immediately. 10.8 Cleaning the oven Clean the oven regularly, each time it is used if possible, after leaving it to cool: in this way it is possible to remove any residue more easily, preventing it from burning the next time the oven is used. Clean the stainless steel parts and enamelled parts as described in the corresponding sections “10.1 Cleaning stainless steel surfaces” and “10.2 Cleaning enamelled surfaces”. Take out all the removable parts and wash them separately. Rinse and dry thoroughly with a clean cloth. 10.8.1 Cleaning the oven door We recommend always keeping the oven door clean. Use kitchen roll and on tougher dirt use a damp cloth and household detergent. Spray products for cleaning the oven must not be used to clean the fan and the thermostat sensor inside the oven compartment. .. Instructions for the user 10.9 Replacing the oven light bulb Proceed as follows: • open the oven door; • unscrew the glass safety cap anticlockwise; unscrew the bulb and replace it with another one for high temperatures (300°C) with the following characteristics: Voltage: 230 V / 50 Hz Power: 15 W Attachment: E 14 • Refit the glass cap and switch on the power. It is possible to check that the oven light is working even when the door is closed by turning the function switch knob to position . .. Instructions for the user 11. Special maintenance Periodically, it is necessary to maintain or replace some parts that are subject to wear and tear. Specific instructions are given below for each type of maintenance. Before carrying out maintenance, switch off the power supply to the appliance and close the gas tap. 11.1 Removing the oven d...
Эта инструкция также подходит к моделям:Плиты - C41022GN (1.45 mb)
Плиты - C41022G (1.45 mb)