Оценок - 3, средний балл: 5
(
)
)
|
Фрагмент инструкции
Resizing with a stainless steel liner may be required. 11. It is recommended that no more than two 90-degree bends be used in the stovepipe installation. More than two 90-degree bends may decrease the amount of draw, and possibly cause smoke spillage. 12. A damper is not required in this installation. Remove the damper plate in the chimney or secure it in the OPEN position. 13. Single wall flue pipe assemblies must not exceed 10 feet in overall length. CHIMNEY REFER TO CHIMNEY AND CHIMNEY CONNECTOR MANUFACTURER’S INSTRUCTIONS CONTACT YOUR LOCAL BUILDING AUTHORITY FOR APPROVED METHODS OF INSTALLATION 1. This appliance requires a masonry or premanufactured chimney listed to UL103HT sized correctly. 2. If a masonry chimney is used, it is advisable to have your chimney inspected for cracks, and check the general condition before installing your unit. Relining may be required to reduce the flue diameter to the appropriate functional size. 3. To help ensure a good draft, the top of the chimney should be at least 3 feet above the point of penetration through the roof, and be at least 2 feet higher than any point of the roof within 10 feet. 4. The chimney connector shall not pass through an attic, roof space, closet, concealed space, floor, ceiling, wall, or any partition of combustible construction. 5. The minimum overall height of your chimney should be 15 feet from the floor. 6. Do not use makeshift compromises during installation. OPERATION Do not use a grate or elevate the fire. Build the wood fire directly on the bricks. When the stove is used for the first time, solvents in the paint will smoke off as the stove "cures.” WOOD - This heater is designed to burn natural wood only. Higher efficiency and lower emissions generally result when burning air-dried seasoned hardwood, as compared to softwood or to green or freshly-cut hardwood. Use only dry, seasoned wood. Green wood, besides burning at only 60 percent of the fuel value of dry wood, deposits creosote on the inside of the stove and along the chimney. This can cause extreme danger of chimney fire. To be called “seasoned,” wood must be dried for a year. Regardless of whether the wood is green or seasoned, it should be stored in a ventilated, sheltered area to allow proper drying during the year. Wood should be stored beyond recommended clearances from combustibles. DO NOT BURN: Treated Wood, Garbage, Solvents, Trash, Cardboard, Colored Paper or Coal. FIRST FIRE - ■ Remember to ventilate well. ■ Allow the stove to cure before burning for long periods of time at high temperatures. ■ Flat spots on the painted surface are normal. ■ Shiny spots on the painted surface (before burning) are normal. ■ Call Customer Service at (800) 245-6489 if you have any questions. BUILDING A FIRE 1. Open the air inlet control fully. 2. Place a small amount of crumpled paper in the stove. 3. Cover the paper with a generous amount of kindling in a "teepee” shape, and a few small pieces of wood. 4. Ignite this fuel and close the door most of the way (leave it open slightly). 5. Add larger pieces of wood as the fire progresses, being careful not to overload. Do not fill the firebox beyond the firebrick area. A coal bed of (ideally) 1” to 2” should be established to achieve optimum performance. 6. This unit is designed to function most effectively when air is allowed to circulate to all areas of the firebox. A good way of achieving this is to rake a small (1” to 2” wide) "trough” in the center of the coal bed, from front to back, prior to loading the fuel. 7. Once fuel has been loaded, close the door and fully open the air inlet control, until the fire is well established (approximately 20 minutes), being careful not to over-fire. 8. Readjust the air inlet control to the desired burn rate. If excessive smoke fills the firebox, open the air inlet control slightly, until flames resume and the wood is sufficiently ignited. Basically, Closed = "Low;” % Way Open = "Medium;” and Fully Open = "High.” 9. When refueling, adjust the air control to the fully open position. When the fire brightens, open the door VERY slowly and carefully. This will prevent gases from igniting and causing smoke and flame spillage. 10. At this point you may add fuel, being careful not to overload. NEVER USE GASOLINE, GASOLINE-TYPE LANTERN FUEL, KEROSENE, CHARCOAL LIGHTER FLUID, OR SIMILAR LIQUIDS TO START OR ‘FRESHEN UP’ A FIRE IN THIS HEATER. KEEP ALL SUCH LIQUIDS WELL AWAY FROM THE HEATER WHILE IT IS IN USE. GLASS CARE REPLACE GLASS ONLY WITH HIGH-TEMPERATURE ROBAX PYROCERAM OF THE PROPER SIZE AND THICKNESS. The following use and safety tips should be observed: 1. Inspect the glass regularly for cracks or breaks. If you detect a crack or a break, extinguish the fire immediately, and contact your dealer or Customer Service at (800) 245-6489 for replacement (or log on to ). 2. Do not slam the door or otherwise impact the glass. When closing doors, ma...
Эта инструкция также подходит к моделям:Плиты - 13-NCG 50-SNC13G 50-TNC13G (819.96 kb)
Плиты - 13-NCC 50-SNC13C 50-TNC13C (819.96 kb)
Плиты - 13-NCP 50-SNC13P 50-TNC13P (819.96 kb)