Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Side View Front View Top View 12" Minimum 12" Minimum 48" Minimum Ceiling Side Wall Side Wall Front of Stove Unit Side Wall Side Wall 12 " Minimum 12 " Minimum 6" Minimum 48" Minimum Ceiling Floor Back Wall Corner Wall Wall 6 " Minimum 6 " Minimum Figure 4 - Minimum Clearance to Walls and Ceiling (Stove May Vary Depending on Model) Continued 104463 7 VENT-FREE NATURAL GAS STOVE HEATER INSTALLATION Continued STOVE CAVITY ASSEMBLY 1. Lift off corrugated box enclosing stove body crating. 2. Remove all screws fastening the wood frame enclosure. Spread wood frame open and lift away from plastic-bagged stove body. The bottom pieces of pallet wood will remain bolted to the stove body. 3. Remove plastic bag from stove body. 4. Remove back panel from stove (see Figure 5). Use an adjustable wrench or a 10 mm socket. Remove six (6) bolts and washers. Keep bolts and washers to reattach back panel later. 5. Remove all contents from inside stove cavity. Contents include: (1) - Stove bottom (4) - Legs (Amity models include leg leveler bolts) (1) - Bottom door (1) - Top grate (1) - Hardware kit bag with fasteners 6. Carefully lay stove body on back to attach bottom components to stove body (see Figure 6). Rest stove on drop cloth or blanket to avoid scratching stove edges. 7. Remove remaining pallet wood attached to bottom of stove body (see Figure 7). Use an adjustable wrench to remove bolts. 8. Fasten each leg to stove with four (4) bolts. Use a flat screw driver to tighten bolt to leg. Thread bolt in tapped holes on stove body (see Figure 8 and Figure 9, page 9). Bolt Product Back Stove Panel Identification Label Figure 5 - Removing Back Panel Top of Stove Unit Figure 6 - Laying Down Stove On Back (Stove Style May Vary Depending on Model) Front of Stove Unit Pallet Wood Bolted to Stove Body Bottom Front of Stove Unit Top of Stove Unit Drop Cloth/ Blanket Front Bolt Pallet Wood Figure 7 - Removing Pallet Wood From The Bottom of The Stove Door Hinge StepBolt Hole Bottom Of Stove Unit Pallet Wood Door Catch Bolt With Adjustable Front Hex Nuts Hole Leg Leg Hole Hole Bottom Of Stove Unit Leg Leg Hole Hole Stove Bottom Holes Figure 8 - Locating Threaded Holes for Stove Bottom, Legs, and Door Attachment (Appearance May Vary Depending on Model) 8 104463 104463 9 OWNER’S MANUAL INSTALLATION Continued Continued Figure 9 - Attaching Stove Legs Bottom Of Stove Unit Leg Bolt Figure 10 - Attaching Stove Bottom Bottom Of Stove Unit Bolt Washers Stove Bottom 9. Fasten stove bottom to stove with four (4) M6 x 1 - 25mm bolts. Use a flat washer and lock washer with each bolt. Tighten bolts into threaded holes on stove body (see Figure 8, page 8 and 10). Use an adjustable wrench or a 10mm socket. Figure 11 - Attaching Stove Door (Appearance May Vary Depending on Model) Step Bolt Door Hinge Threaded Hole Stove Door Bolt Stove Bottom Shoulder Door Hinge Step Bolt Bolt Shoulder Adjusting Nut Bolt Stop Catch Bolt Door Door Claw Figure 12 - Catch Bolt and Door Claw Orientation Stove Door 10. Attach stove door by inserting step bolt through door hinge pivot holes and into threaded hole in stove body (see Figure 11). Use an adjustable wrench or a 12mm socket to fasten step bolt. Tighten step bolt until snug. Make sure door moves freely. 11. Install door catch bolt (M8 x 1.25- 55mm with two M8 hex nuts) into threaded hole on stove body (see Figure 8, page 8). Use an adjustable wrench or a 12mm socket. The catch bolt has two hex nuts attached to it (see Figure 12). The top nut is a bolt stop and the bottom nut is for door leveling adjustment. 12. Check general catch bolt alignment with door claw. Make final adjustment and door leveling after stove is in normal standing position. 13. Carefully lift stove back up on its four attached legs. 14. If available, install gas log heater inside stove cavity before installing the back panel (see Installing Gas Log Heater Into Stove, page 10). 15. Fasten back panel to stove with six (6) M6 x 1 - 20mm bolts and washers. Make sure product identification label is located on the outside in lower lefthand corner. 10 104463 VENT-FREE NATURAL GAS STOVE HEATER INSTALLING GAS LOG HEATER INTO STOVE 1. Remove log and gas log heater from carton. Note: Do not pick up gas log heater by the burner itself. This could damage heater. Always handle the gas log heater by the heater base only. 2. Remove all protective packaging applied to log and gas log heater for shipment. 3. Check all items for any shipping damage. If damaged, promptly inform dealer where you bought heater. 4. If not already removed, remove back panel from assembled stove body (see Figure 5, page 8). Use an adjustable wrench or a 10 mm socket. Remove six (6) bolts and washers. Keep bolts and washers to reattach back panel later. 5. Set gas log heater inside stove (see Figure 13). Make sure control knob extensions pass through bottom front opening. 6. Align outside holes on heater base with four (4) mounting holes on the stove bottom (see Figure 13). INSTALLATIO...