Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Check your local codes. Use pipe of 1/2" diameter or greater to allow proper gas volume to heater. If pipe is too small, undue loss of volume will occur. Installation must include an equipment shutoff valve, union, and plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge hook up. NPT tap must be upstream from heater (see Figure 8, page 9). IMPORTANT: Install equipment shutoff valve in an accessible location. The equipment shutoff valve is for turning on or shutting off the gas to the appliance. Check your building codes for any special requirements for locating equipment shutoff valve to fireplaces. Apply pipe joint sealant lightly to male NPT threads. This will prevent excess sealant from going into pipe. Excess sealant in pipe could result in clogged heater valves. Side View Back View Figure 6 - Gas Regulator Location and Gas Line Access Into Stove Cabinet Back Stove PanelFront of Stove Unit Gas Inlet Connection Access Product Identification Label Gas Log Heater Propane/LP Supply Tank Vent Pointing External Regulator Down Figure 7 - External Regulator For Propane/LP Gas With Vent Pointing Down For more information, visit more information, visit 111487-01B INSTALLATION Connecting to Gas Supply (Cont.) Checking Gas Connections 9 INSTALLATION Continued WARNING: Use pipe joint sealant that is resistant to liquid petroleum (LP) gas. We recommend that you install a sediment trap in supply line as shown in Figure 8. Locate sediment trap where it is within reach for cleaning. Install in piping system between fuel supply and heater. Locate sediment trap where trapped matter is not likely to freeze. A sediment trap traps moisture and contaminants. This keeps them from going into heater controls. If sediment trap is not installed or is installed wrong, heater may not run properly. CAUTION: Avoid damage to regulator. Hold gas regulator with wrench when connecting it to gas piping and/or fittings. CSA Design-Certified Tee Pipe Cap Joint Nipple 3" Minimum Sediment Trap Gas Regulator (Propane/LP) From External Regulator (11" W.C.** to 14" W.C. Pressure) Equipment Shutoff Valve With 1/8" NPT Tap* Approved Flexible Gas Hose (if allowed by local codes) Figure 8 - Gas Connection * Purchase the optional CSA design-certified equipment shutoff valve from your dealer. See Accessories, page 17. ** Minimum inlet pressure for purpose of input adjustment. CHECKING GAS CONNECTIONS CAUTION: Make sure external regulator has been installed between propane/LP supply and propane/ LP heater. See guidelines under Connecting to Gas Supply, page 8. Pressure Testing Gas Supply Piping System Test Pressures In Excess Of 1/2 PSIG (3.5 kPa) 1. Disconnect appliance with its appliance main gas valve (control valve) and equipment shutoff valve from gas supply piping system. Pressures in excess of 1/2 psig will damage heater regulator. 2. Cap open end of gas pipe where equipment shutoff valve was connected. 3. Pressurize supply piping system by either opening propane/ LP supply tank valve for propane/LP gas or opening main gas valve located on or near gas meter for natural gas, or using compressed air. 4. Check all joints of gas supply piping system.Apply noncorrosive leak detection fluid to gas joints. Bubbles forming show a leak. 5. Correct all leaks at once. 6. Reconnect heater and equipment shutoff valve to gas supply. Check reconnected fittings for leaks. Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa) 1. Close equipment shutoff valve (see Figure 9). 2. Pressurize supply piping system by either opening propane/ LP supply tank valve for propane/LP gas or opening main gas valve located on or near gas meter for natural gas, or using compressed air. 3. Check all joints from gas meter for natural or propane/LP supply to equipment shutoff valve (see Figure 10 or 11, page 10). Apply noncorrosive leak detection fluid to gas joints. Bubbles forming show a leak. 4. Correct all leaks at once. Open Equipment Shutoff Valve O S Closed Figure 9 - Equipment Shutoff Valve WARNING: Test all gas piping and connections, internal and external to unit, for leaks after installing or servicing. Correct all leaks at once. WARNING: Never use an open flame to check for a leak. Apply a noncorrosive leak detection fluid to all joints. Bubbles forming show a leak. Correct all leaks at once. For more information, visit more information, visit 111487-01B 111487-01B Forr morre iinfforrmattiion,, viisiitt 10 INSTALLATION Continued Figure 10 - Checking Gas Joints on Propane/LP Gas Unit Control Valve Location Propane/LP Supply Tank Equipment Shutoff Valve Pressure Testing Heater Gas Connections 1. Open equipment shutoff valve (see Figure 9, page 9). 2. Open main gas valve located on or near gas meter for natural gas or open propane.LP supply tank valve. 3. Make sure control knob of heater is in the OFF position. 4. Check all joints from equipment shutoff valve to contr...