Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Touch Up Paint Included with the owner's pack of this appliance is a can of Stove-Brite® paint. To touch up nicks or dulled paint, apply the paint while the appliance is cool. Sand rusted or damaged areas before preparation (use 120 grit sandpaper). Clean and dry the area to prepare the surface. Wait at least one hour before starting the appliance. The touched up area will appear darker than the surrounding paint until it cures from heat. Curing will give off some fumes while curing – open windows to ventilate. Cleaning the Air Duct and Blower (if applicable) Use a vacuum to clean the air ducts (channels). This prevents dust from burning and creating odors. Touch-Up P a i n t The optional blower should be vacuumed every year to remove any buildup of dust, lint, etc. Use a vacuum cleaner to remove any buildup on the screens of the blower. BOTTOM OF STOVE Adjusting the Bypass Latch The bypass latch uses a pressure plate to secure it in the closed position. If the bypass does not latch to the closed position, it may be adjusted following the directions below. Close the bypass -- you may need to hold it in the shut position. Tighten this bolt 1/2 turn. Test operation of the bypass - opening and closing it several times. If it does not latch shut, tighten the bolt another 1/2 turn. NOTE: In rare cases the bolt may be over-tightened, not allowing the bypass handle to rotate down. in these cases, loosen the bolt. Verify Cast Iron Fasteners Verify the fasteners holding the cast iron components are properly tightened. Bypass Plate 7/16" Wrench © Travis Industries 100-01190_000 4070326 Maintaining Your Appliance 31 Maintaining Your Appliance 31 Door Parts 5 9 8 10 4 3 7 2 6 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA1 ID # Description Qty Part # ID # Description Qty Part # 1 Door, Left 1 2 Door, Right 1 3 Door Gasket 1 4 Gasket Cement 1 5 Glass Gasket 1 6 Glass 2 7 Glass Clip w Screws, Gasket 4 8 Door Hinge w Pins 4 9 Left Door Handle w Hardware 1 10 Right Door Handle w Hardware 1 Replacing the Glass The glass must not contact the door retainer or glass clips directly. The glass gasket and glass clip gaskets insulate the glass to prevent cracking. Do not over-tighten the glass clips. Replacing the Door Gasket The door gasket inserts into the outer groove of the door. Stove gasket cement holds it in place. Before installing, remove any residual cement. Lay the gasket in place (start at the lower left corner) and cut off any excess gasket (do not stretch the gasket. The cement fully cures with heat from the stove. You may need to open and close the door repeatedly to get the gasket to seat fully. Replacing the Loading Lid Gasket The loading lid gasket inserts into the groove below the loading lid. Stove gasket cement holds it in place. Before installing, remove any residual cement. Lay the gasket in place (start at the back left corner) and cut off any excess gasket (do not stretch the gasket. The cement fully cures with heat from the stove. You may need to open and close the lid repeatedly to get the gasket to seat fully. Replacing the Door Handle See the illustration above for a component list (see pg. 29 for details on adjusting the door). © Travis Industries 100-01190_000 4070326 32 Maintaining Your Appliance 32 Maintaining Your Appliance Firebox Parts 4 21 1 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA 7 9 6 3 5 8 7 ID # Description Qty Part # ID # Description Qty Part # 1 Side Brick 2 250-00139 2 Combustion Brick 1 250-00141 3 Interram Gasket 1 250-00294 4 Back Brick 1 250-00140 5 Firebox Back 1 6 Combustor 1 250-00247 7 Brick Clips with Bolts 1 250-00144 8 Combustion Brick Gasket 1 9 Firebox Back Screw 4 3 Brick Removal & Replacement Do not pry brick - they chip and crack easily. Remove the clips holding the side brick in place. Remove the side brick. Remove the clip holding the back brick in place. Lift the back brick up and remove. Remove the gasket on top of the combustion brick. Remove the combustion brick. Combustor Removal & Replacement Remove the bricks first. Remove the rear heat shield (the screws holding the firebox back are held in place with nuts accessible from the back of the stove). Remove the firebox back (use a wrench to secure the nuts on the back of the stove will un-screwing the 4 screws holding the firebox back in place). Remove the bypass assembly (two nuts and two bolts hold it in place – take care when removing to prevent damage). Slide the combustor forward to remove. © Travis Industries 100-01190_000 4070326 Limited 5 Year Warranty 33 Limited 5 Year Warranty 33 To register your TRAVIS INDUSTRIES, INC. 5 Year Warranty, complete the enclosed warranty card and mail it within ten (10) days of the appliance purchase date to: TRAVIS INDUSTRIES, INC., 4800 Harbour Pointe Blvd. SW, Mukilteo, WA 98275. TRAVIS INDUSTRIES, INC. warrants this appliance (appliance is defined as the equipment manufactured by Travis Industries, Inc.) to be defect-free in material and workmanship to the original p...