Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Fit new gasket/seal to new valve. Reassemble in reverse order. Check valve is adjusted for correct gas. Check range is gas sound. 5 SERVICING - WARNING Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished. burners. Remove the screw at the front holding top of range with cooktop removed 10. To Change Cooktop Burner Orifice Remove burner cap and head. Remove old jet. Fit new orifice. Note the Wok burner has 2 orifices. Reassemble in reverse order. Check appliance is gas sound. 11. To Change Cooktop Burner Electrode Lift off cooktop grates, remove burner cap. Remove the screw holding the electrode. Pull electrode vertically up sufficiently to grip the lead between thumb and forefinger. Pull off the electrode, but keep hold of the lead. Fit new electrode to the lead. Fix electrode in burner with screw. Replace burner cap. Check the burner ignition. Replace grates. 12. To Remove or Change a Cooktop Burner. Remove the cooktop tray (see 3). Center cooktop burners Remove the control panel (see 2). The burners are mounted in 2’s on cross supports. Disconnect the burner feed pipes at the the cross support. Slide the support to the right to release in from the rear location. Lift the cross support and burners clear. The burners are fixed to the cross supports with screws underneath Remove the appropriate burner and fit the new one. Reassemble in reverse order. Check burner operation is satisfactory. Wok burners Disconnect the burner feed pipes at the burner. Fit the new one and reassemble in reverse order. Check burner operation is satisfactory. 6 SERVICING - WARNING Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished. 13. To Remove Broiler Outer Door 15. To Change Oven Door Outer Panel Open left hand oven door and remove 2 screws from bottom edge of broiler door. Open broiler door, support broiler door outer panel and remove two screws from top inner face of broiler door. There is a pad of fibre insulation inside the door. Reassemble in reverse order making sure that the pad of insulation is in place. 14. To Remove an Oven Door Open oven door and remove Handyrack (where fitted) by springing one side out of the bracket on the door and sliding the other side free. Support the door and remove the two screws securing the upper hinge and packing to the cooker front. Remove the door from the lower hinge by lifting slightly and moving outwards. Reassemble in reverse order. Panel Remove the two plastic blanking plugs from the door handles. Remove the 4mm Hex headed screws holding the handle to the door with the hexagon key tool. Remove two screws from top edge and two from bottom edge of the door. Remove outer door panel. Fit door handle to new panel. Fit the plastic blanking plugs to the fixing holes. The handles should be above the fixings. Fit panel to door. If replacing the outer panel on the right hand door (with the Thermodial) take care to make sure the sensor of the Thermodial is sealed to the door by the rubber grommet. Reassemble in reverse order. 7 SERVICING - WARNING Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished. 16. To Change Oven Door Catch Remove outer door panel (see 15). Remove screws ‘B’ holding catch assembly to inner door panel. Fit new catch and reassemble in reverse order. Check correct door operation. 17. To Change Oven Door Seal Open oven door. The seal is held in place by small hooks on the rear face. At the corner pull seal diagonally away from the door centre until that hook is released. Proceed to the next hook and release it in a similar way, and so on. Fig. 4 When fitting new seal, position the seal join at the bottom. Hook the new seal in one of the corner holes of the door, and proceed round the door snapping in each hook in turn. 18. To Adjust Oven Door Catch Keep Open oven door, slacken off locknut at base of keep, and screw in or out as required until required fit is obtained. Retighten locking nut. 19. To Change Ignition Generator Disconnect from electricity supply. Pull cooker forward to gain access to the cover box at the rear of the left hand cooker. Remove the screws securing the cover and lift clear. Pull off all the leads to the generator noting their positions. Slacken the two screws holding generator to cooker and remove generator. Fit new generator to cooker and replace leads. Reassemble in reverse order. Refer to wiring diagram. Check ignition performance. 20. To Remove Oven Inner Back. Open the oven door. Remove oven furniture. For the LH oven unscrew the 2 thermostat phial fixing screws. Remove the fixings that secure the inner back to the oven rear. Lift the removable panel away. Re-assemble in reverse order. Ensure that the retaining fixings are fully tightened. For the LH oven unscrew the 2 thermostat phial fixing screws. Remove the screws that secure the inner back to the oven rear. Lift the removable 8 SERVICING - WARNING D...