Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
F104650-01 Contents Servicing Notes 1. To Remove the Hand Rail 2. To Remove Control Panel 3. To Remove the Cooktop 4. To Remove a Side Panel 5. To Remove Oven Light Switch 6. To Remove Electronic Timer 7. To Remove a Thermostat 8. To Change Broiler Controller 9. To Change a Cooktop Tap 10. To Change a Cooktop burner orifice 11. To Change Cooktop Burner Electrode 12. To Remove or Change a Cooktop Burner. 13. To Remove Broiler Outer Door Panel 14. To Remove Main Oven Door 15. To Change Main Oven Door Outer Panel 16. To Change Main Oven Door Catch 17. To Change Oven Door Seal 18. To Adjust Oven Door Catch Keep 19. To Change Ignition Generator 20. To Remove Oven Inner Back. 22. To Replace an Oven Fan 23. To Remove an Oven fan Element 24. To Remove Broiler Element. 25 To Remove the LH Oven Bottom and Top Elements 26. To change Main oven light bulb. 27 To Remove Tall Oven Door 28. To Change Tall Oven Door Outer Panel 29. To Change Tall Oven Door Magnetic Latch 30. To Replace the Cooling fan Schematic diagram of the Range Technical Data SERVICING - WARNING Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished. Servicing Notes When servicing or replacing gas carrying components disconnect from gas before commencing operation and check appliance is gas sound after completion. When checking for gas leaks use a liquid leak detector at all joints and connections to check for leaks in the system. Use a product specifically manufactured for leak detection. Leak testing of the appliance shall be conducted in accordance to the manufacturer’s instructions. CAUTION: DO NOT USE A FLAME TO CHECK FOR GAS LEAKS. Do not use re-conditioned or unauthorised gas controls. Disconnect from electricity supply before commencing servicing, particularly before removing any of the following: control panel, side panels, cooktop tray, or any of the electrical components or cover boxes. Before electrical reconnection make sure the range is electrically safe. 1. To Remove the Hand Rail Remove the handrail plastic blanking plugs and remove the 2 end bracket fixing screws. 2. To Remove Control Panel Disconnect from electricity supply. Pull off all the control knobs. Remove the handrail (see 2) Remove the 2 cross headed screws that were hidden by the handrail end brackets. Open the broiler door and R H oven door and remove the 2 screws underneath the control panel. Pull the control panel forward and support so that the wires are not strained. Reassemble in reverse order. When replacing leads refer to the wiring diagram. Check operation of timer, ignition, and oven light switches. 3. To Remove the Cooktop Disconnect from electricity supply. Remove the pan supports, cooktop burner caps and tops. If there are screws holding the cooktop burners to the cooktop, remove them (not the spark electrode fixing screws). A Cooktop front fixing screws B Cooktop rear fixing screws Remove the 4 rear cooktop fixing screws (B) and the 4 front cooktop fixing screws (A). Remove the screws holding the flue grille stays. Lift the cooktop clear of the appliance. Replace in reverse order. Reassemble in reverse order ensuring that the leads are reconnected. Check for correct burner operation. 4. To Remove a Side Panel Disconnect from electricity supply. Remove control panel (see 2). Pull the cooker forward. Remove the 4 retaining screws for each panel (2 at the front and 2 at the rear). The lower front retaining screws (one each side) are situated beneath the lower edge at the front corners of the side panels Reassemble in reverse order. 4 SERVICING - WARNING Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished. 5. To Remove Oven Light Switch 6. To Remove Electronic Timer Remove control panel (see 2). Disconnect from electricity supply. NB The old switch may be destroyed during Pull off the timer control buttons and remove removal. the control panel (See 2). Remove the timer/ Remove switch button and old switch from its mounting bracket assembly from the control panel bezel by gripping the switch body behind the by removing the two fixing screws. Remove the control panel and twisting sharply. timer from its mounting bracket by depressing the The switch bezel can then be removed by folding plastic lugs on the timer case, at the same time back its locking wings and pushing forward. Fit pulling the unit forward. the new bezel to the control panel by first lining Reassemble in reverse order. When replacing up the raised key on its body with the cutout in leads refer to the wiring diagram. Check operation the control panel and pushing it in from the front. of timer. Assemble the new switch to the bezel by lining up the key sections and pushing home. Fit the new button by pushing in from the front. Replace control panel in reverse order and test for correct operation. 5 SERVICING - WARNING Disconnect from electricity and gas before servicing. Check appliance is safe...