Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Notes • Replace the batteries when the OPR/BATT indicator dims or when the player stops operating. Replace all the batteries with new ones. Before you replace the batteries, be sure to take out the CD from the player. • To use the player on batteries, disconnect the mains lead from the player. • When you operate the player on batteries, you cannot turn on the player using the remote. Preparing the remote C Insert two R03 (size AAA) batteries (not supplied). Replacing battery With normal use, the batteries should last for about six months. When the remote no longer operates the player, replace all the batteries with new ones. Printed on 100% recycled paper using VOC (Volatile Organic Compound)- free vegetable oil based ink. MEGA BASS VOLUME –, +* ., > TUNE –, + MODE x u* OPERATE (POWER) SLEEP OPR/BATT Loading a CD With the labeled side up Inserting a cassette With the side you want to play facing you CD RADIO BAND AUTO PRESET TAPE Display Z PUSH OPEN/CLOSE DISPLAY ENT MEMORY OPTICAL DIGITAL OUT (CD) (CFD-S300L only) LINE (CFD-S300L only) * iLINE IN (CFD-S300L only) MEGA BASS VOLUME –, +* ., > TUNE –, + MODE x u* OPERATE (POWER) SLEEP OPR/BATT Loading a CD With the labeled side up Inserting a cassette With the side you want to play facing you CD RADIO BAND AUTO PRESET TAPE Display Z PUSH OPEN/CLOSE DISPLAY ENT MEMORY OPTICAL DIGITAL OUT (CD) (CFD-S300L only) LINE (CFD-S300L only) * iLINE IN (CFD-S300L only) 3 Press DISPLAY•ENT•MEMORY. The stations are stored in memory from the lower frequencies to the higher ones. If a station cannot be preset automatically You need to preset a station with a weak signal manually. 1 Press RADIO BAND•AUTO PRESET to select the band. 2 Tune in a station you want. 3 Hold down the number buttons that you want to preset the new station on for about 2 seconds. To select the preset number over 10, press >10 first, then the corresponding number buttons. You need to hold down the last number button to enter for about 2 seconds. (Example: To select 12, press >10 and 1 first, then hold down 2 for about 2 seconds.) Tip • Adjusting the volume or the audio emphasis will not affect the recording level. • If the AM/MW/LW programme makes a whistling sound after you've pressed z in step 3, press MODE to select the position of ISS (Interference Suppress Switch) that most decreases the noise. • For the best results, use the AC power as a power source for recording. • To erase a recording, proceed as follows: 1 Insert a tape with the recording you want to erase. 2 Press TAPE. 3 Press z. To turn on/off the power CFD-S300L: Press OPERATE. tthe current track number and playing time rthe current track number and the remaining time on the current track* rthe number of tracks left and remaining time on the CD * For a track whose number is more than 20, the remaining time appears as “- -:- -” in the display. Selecting the play mode Press MODE until “REP 1” “REP ALL” “SHUF” “SHUF REP” “PGM” “PGM REP” appears in the display. Then proceed as follows: Number buttons Remote sensor Total track number Programmed track Playing order DETotal playing time Display * For MiniDisc recorder: a cable with a stereo-mini plug on both ends. * For TV, VCR: a cable with a stereo-mini plug on one end and two phono plugs on the other end. 2 Press LINE to display “LInE”. 3 Play the optional component connected to the LINE IN jack of the player. Tip You can record the sound from the connected component. Insert a blank tape into the tape compartment, Location of controls Remote Control OPERATE (POWER) FUNCTION BAND u .,> PRESET –, + x VOL –, +* *The button has a tactile dot. Playing a CD 1 Press CD (direct power-on). (On the remote, press OPERATE (or POWER) and then press FUNCTION reapeatedly until “Cd” appears in the display.) 2 Load a CD in the CD compartment. 3 Press Z PUSH OPEN/CLOSE to close the CD compartment. 4 Press u. The player plays all the tracks once. To Press stop playback x pause playback u Press the button again to resume play after pause. go to the next track > go back to the previous track . remove the CD Z PUSH OPEN/CLOSE locate a specific track directly* a number button of the track locate a point while listening > (forward) or . (backward) while playing until you to the sound find the point locate a point while observing > (forward) or . (backward) in pause until you find the display the point * You cannot locate a specific track if “SHUF” or “PGM” is lit in the display. Turn off the indication by pressing x. Tip To locate a track numbered over 10, press >10 first, then the corresponding number buttons. Example:To play track number 23, press >10 first, then 2 and 3. Using the display To check the total track number and playing time Press DISPLAY•ENT•MEMORY in stop mode (see fig. D). To check the remaining time Press DISPLAY•ENT•MEMORY repeatedly while playing a CD. The display changes as follows: Listening to the radio 1 Press RADIO BAND•AUTO PRESET until the band you want appears in the display (direct powe...
Эта инструкция также подходит к моделям:Плееры - CFD-S300 (119.93 kb)