Оценок - 0, средний балл: 4
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
. When the batteries are not to be used, remove them to avoid damage that can be caused by battery leakage or corrosion. On placement . Do not leave the unit in a location near heat sources, in a place subject to direct sunlight, excessive dust or mechanical shock or in a car subject to the direct rays of the sun. . Do not place the unit on an inclined or unstable place. . Do not place anything within 10 mm of the side of the cabinet. The ventilation holes must be unobstructed for the unit to operate properly and prolong the life of its components. . Since a strong magnet is used for the speakers, keep personal credit cards using magnetic coding or springwound watches away from the unit to prevent possible damage from the magnet. On operation . If the unit is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lens inside the CD player section. Should this occur, the unit will not operate properly. In this case, remove the CD and wait about an hour for the moisture to evaporate. . If the unit has not been used for a long time, set it in the playback mode to warm it up for a few minutes before inserting a cassette. Notes on cassettes . Break off the cassette tab from side A or B to prevent accidental recording. If you want to reuse the tape for recording, cover the broken tab with adhesive tape. Tab for side B Tab for side A Side A . The use of a cassette with more than 90 minutes of play time is not recommended except for long, continuous recording or playback. Cleaning the cabinet . Clean the cabinet, panel and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent, such as alcohol or benzine. If you have any questions or problems concerning your unit, please consult your nearest Sony dealer. General The power is not on. . Connect the AC power cord to the wall outlet securely. . Make sure the batteries are inserted correctly. . Replace all the batteries with new ones if they are weak. . You cannot turn on the unit with the remote when you operate the unit on batteries. There is no audio. . Make sure the function you want to use appears in the display window. . Unplug the headphones when listening through speakers. The display and indicators are flashing randomly even when the power is turned off. . The demo mode is on. Turn on the power, or disable the demo mode when the power is off. Noise is heard. . Someone is using a portable telephone or other equipment that emits radio waves near the unit. . Move the portable telephone, etc., away from the unit. The AUDIO IN lid has been detached. . Reattach the lid as shown in the illustration below. (Reattach in order of . and ..) CD/MP3/WMA player The CD does not play or “NO DISC” is displayed even when a CD is in place. . Place the CD with the label surface up. . Clean the CD. . Take out the CD and leave the CD compartment open for about an hour to dry moisture condensation. . The CD-R/CD-RW is blank. . There is a problem with the quality of the CD-R/ CD.RW, recording device or application software. . Replace all the batteries with new ones if they are weak. The sound drops out. . Reduce the volume. . Clean the CD, or replace it if the CD is badly damaged. . Place the unit in a location free from vibration. . Clean the lens with a commercially available blower. . The sound may drop out or noise may be heard when using a poor quality CD-R/CD-RW or if there is a problem with the recording device or application software. Starting playback takes more time than usual. . The following discs take a longer time to start playback. – a disc recorded with a complicated tree structure. – a disc that has not been finalized (a disc to which data can be added). – a disc that has many folders or non-MP3/WMA files. Radio Reception is poor. . Reorient the antenna to improve FM reception. . Reorient the unit itself to improve AM reception. The audio is weak or has poor quality. . Replace all the batteries with new ones if they are weak. . Move the unit away from the TV. . If you are using the remote while listening to AM radio, noise may be heard. The picture of your TV becomes unstable. . If you are listening to an FM program near the TV with an indoor antenna, move the unit away from the TV. USB device Are you using a compatible USB device? . If you connect an incompatible USB device, the following problems may occur. See “Playable/ Recordable USB devices” for a list of devices that are supported. – The USB device is not recognized. – File or folder names are not displayed on this unit. – Playback is not possible. – The sound skips. – There is noise. – The sound output is distorted. “OVER CURRENT” appears. . An abnormal level has been detected in the electrical current from the . (USB) port .. Turn off the unit and remove the USB device from the . (USB) port .. Make sure there is no problem with the USB device. If this message persist...