Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
When you check out a track from your computer, the recorder needs a 2-second (or 4or 8-second) space for a track even if the track is under 2 seconds (or 4 or 8 seconds) in length. Also, the recorder inserts a 2-second (or 4 -or 8-second) space in between tracks during check out so as not to overwrite the previous track by mistake. For this reason, the recorder needs an additional 6 seconds (or 12 or 24 seconds) for each track. This reduces the maximum recording time for each track by 6 seconds (or 12 or 24 seconds) during check out. You cannot erase a track checked out from your computer. To erase a track that has been checked out from your computer, check it back in first, and then erase it using the OpenMG Jukebox software. When using with the AC The recorder turns off 3 minutes after the recorder has power adaptor, the display stopped in order to allow the charging time on the USB window of the recorder will cradle to be calculated. remain faintly lit for some time even after the recorder is stopped. Troubleshooting Should any problem persist after you have made these checks, consult your nearest Sony dealer. Refer to “Messages” (page 90) as well. Symptom Cause/Solution The recorder does • Audio sources may not be securely connected. not work or works , Disconnect the audio sources once and connect them again poorly. (pages 20, 29). • The HOLD function is turned on (“HOLD” appears in the display when you press an operation button on the recorder). , On the recorder, disable HOLD by sliding the HOLD switch to the opposite direction of the arrow (pages 17, 72). • The lid is not firmly closed. , Close the lid until it clicks. Then press OPEN to open the lid. • Moisture has condensed inside the recorder. , Take the MD out and leave the recorder in a warm place for several hours until the moisture evaporates. • The rechargeable battery or dry battery is weak (“LOW BATT” flashes or nothing appears). , Charge the rechargeable battery or replace the dry battery with the new one (page 16), or connect the supplied AC power adaptor to the recorder. • The rechargeable battery or dry battery have been inserted incorrectly. , Insert the battery correctly (page 15). • When recording digitally from a portable CD player, you did not use AC power or did not disable the anti-skip function such as ESP (page 22). • The analog recording was made using a connecting cord with an attenuator. , Use a connecting cord without an attenuator (page 29). • The AC power adaptor was unplugged during recording or a power outage occurred. • While operating, the recorder received a mechanical shock, too much static, abnormal power voltage caused by lightning, etc. , Restart the operation as follows. 1 Disconnect all the power sources. 2 Leave the recorder for about 30 seconds. 3 Connect the power source. • The disc is damaged or does not contain proper recording or editing data. , Reinsert the disc. Rerecord the disc. If the error message still appears, replace it with another disc. • Recording level is too small to record (when recording manually). , Pause the recorder and adjust the recording level. Symptom Cause/Solution The recorder does not work or works poorly. • The recorder is operated when it is on a battery charging stand. , Remove the recorder from the battery charging stand. • You tried to turn group mode on while setting the program. , Turn group mode on before setting the program. • There is an internal malfunction in the system. , Remove the recorder from the USB cradle, restart your computer, and then place the recorder on the USB cradle again. The recorder does not work while connected to the computer. • The computer does not recognize the recorder. , Verify that the recorder is correctly connected. , Place the recorder correctly on the USB cradle. , Install the driver correctly into your computer. , Install the OpenMG software into your computer first, and then connect the recorder. The recorder • The record starting-position setting (“REC-Posi”) is set to “From overwrites Here”. existing materials , Set “REC-Posi” setting to “From End”. when record. “NO SIGNAL” appears in the display when recording from a portable CD player. • There is no digital signal from the portable CD player. , When recording digitally from a portable CD player, use the AC power adaptor and disable the anti-skip function (such as ESP) on the CD player (page 22). There is no recording on the MD after a recording operation. • The AC power adaptor was unplugged or a power outage occurred during recording. The lid does not open. • The power sources have been disconnected during recording or editing, or the battery have been exhausted. , Set the power sources again, or replace the exhausted battery with new ones. • Check-in/Check-out is not finished. , After the dialog box in the display window of your computer disappears and the display window of the recorder indicates that the recorder has stopped, flip the control bar towards x on the recorder and re...