Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Problem Does not operate. Cannot play the MD. Tracks on MD do not play in order, starting with the first track. Cannot hear music—too noisy. TV picture is distorted. Radio reception is noisy. Power is not turned on. Charging indicator does not light during charging. E Check this Is the MD loaded? If unloaded, “No Disc” will appear on the display. • Is the HOLD switch released? • Is the battery low? • Is there moisture condensation on the lens? (Wait for about an hour and then try again.) • Is the Repeat Play or Random Play selected? • You stopped or turned off the power while playing. It changed to Resume Play. • Is the headphone plug inserted all the way? • Is the plug dirty? (Wipe away dirt on the plug.) • Is music recorded on the MD? If not, “BLANK” will appear on the display. • Is the unit too near a TV or tuner? (If the TV or tuner is connected to a simple indoor antenna, connect it to an outdoor antenna.) • With both HOLD switches activated, the battery was changed during playback. (Release both HOLD switches and try to operate again.) • Is the charger too hot? (If so, disconnect the AC adaptor and leave the charger for a while.) Specifications Portable MINIDISC player Type : Minidisc digital audio system Sampling frequency : 44.1 kHz Compression/expansion method : ATRAC method Number of channels : 2 channels (stereo) Frequency response : 20 Hz to 20,000 Hz Wow & flutter : Unmeasurable Output : Headphone (3.5 mm dia. stereo . 1) 5 mW/ch at 10% THD/16 ohms to 47 kohms Duration of battery : Approx. 20 hours when using a rechargeable battery (BN-R1210) charged for 2 hours; * Above duration may differ depending on the ambient temperature and conditions. Power requirements : DC 1.2 V (rechargeable battery) Dimensions (L . W . H) : 76 mm . 17.5 mm . 80.5 mm (Excluding buttons and controls) Mass : Approx. 83 g (without battery) AC adaptor (AA-R9020) Input power source : AC 110-AC 230 V, 50 Hz/60 Hz Output voltage : DC 9 V, 0.5 A Charger (AC-R126) Input power source : DC 9 V, 0.5 A Design and specifications are subject to change without notice. US and foreign patents licensed from Dolby Laboratories Licensing Corporation. Muting the pip tone When you press a button on the remote control except for the A.C.BASS and VOLUME (+, –) buttons, a pip tone is emitted. To mute the pip tone, while pressing the A.C.BASS button in Stop mode or during playback, press the P.MODE button. “BEEP OFF” appears on the remote control display. To resume the pip tone, do the same operation again. “BEEP ON” will appear on the display. Using the Minidisc Player with Optional Accessories Using the minidisc player with an audio system You can listen to MDs through your audio system. • After turning off the amplifier, plug a stereo connection cable (not supplied) into the headphones jack as shown below. • Adjust the volume of the minidisc player to an appropriate level. • Adjust the volume level on the amplifier. • Use the unit's buttons for operation. (The remote control will issue a Pip tone.) • Direct connection without passing through the remote control may generate noise. • Depending on the connected device, the sound may not be as loud as the sound from other sources. This is because the sound level has been adjusted for the headphones and is not a malfunction. Using the minidisc player with a car audio system You can listen to an MD through your car audio system. The following accessories are available for your car audio system. • Car audio cassette adaptor CAUTION: • Connect the car audio cassette adaptor to the remote control headphone jack. The other end connects to the cassette slot of your car. • Adjust the volume level of the unit to an appropriate level. EN, CH Normal Play Follow the numbers in the figure to the right. 1 Connect the headphones plug firmly. 2 Connect the remote control plug firmly. 3 Make sure the switches on the unit and remote control are not on HOLD setting. 4 Load an MD. • Slide the OPEN switch to open the lid. • Open the lid by hand. • Insert the MD into the MD slot beneath the lid, with its label side facing up. Insert the MD until it stops. Be sure the % or ] mark on the MD aligns as shown in the figure. • Close the lid. “HELLO” appears on the remote control display. Then the track number and playback time appear. 5 Adjust the volume level between 0 and 25. Press the Volume (+, –) button on the unit or the remote control. 6 Press the 3/8 button. Playback starts from the first track and ends after playing all the tracks on the MD. Notes: • Insert the MD in the way that it will not touch the catch. If the catch is bent for some reason, the lid may not be closed properly. • When opening the lid, please hold it by the edge when an MD is already loaded. • If no MD is loaded, “No Disc” appears on the display, and the power will automatically shut off after approx. 10 seconds. • If the MD is recorded in Monaural mode, “MONO” will appear on the display. • To eject the MD, slide the OPEN switch and open the li...
Эта инструкция также подходит к моделям:Плееры - XM-PX33BU (367.78 kb)