Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
2. Replace the compartment door, making sure the batteries are firmly and correctly in place. The set is now ready to operate. 3. Remove the batteries if the set is not to be used for a long time. Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst. Therefore: • Do not mix battery types: e.g. alkaline with carbon zinc. Only use batteries of the same type for the set. • When inserting new batteries, do not try to mix old batteries with the new ones. • Remove the batteries if the set is not to be used for a long time. Using AC POWER 1. Check if the power voltage as shown on the type plate on the base of the set, corresponds to your local power supply. If it does not, consult your dealer or service center. 2. Connect the power cord to the MAINS inlet and the wall outlet. The power supply is now connected and ready for use. 3. To switch off completely, withdraw the power cord from the wall outlet. – Disconnect the power cord from the wall outlet to protect your set during heavy thunderstorms. Batteries contain chemical substances, so they should be disposed of properly. The type plate is located on the bottom of the set. Switching POWER on/off: Save energy Whether you are using mains or battery supply, to avoid unnecessary energy consumption always push the POWER button to the off position after using the set. AC MAIN AC MAINS English 9 SPEAKERS English REMOVABLE LOUDSPEAKERS Taking off the speakers Keep the lever (found on the back corner of the speaker) pressed and slide the speaker upwards. Attaching the speakers Slide the speakers from above into the sleeves on the sides of the cabinet. The speakers will click into position. CONNECTING THE SPEAKERS 1. Connect the right speaker to the R terminal, with the red marked wire to "+" and the black wire to "-". 2. Clip the exposed portion of wire into the corresponding color terminal. 3. Repeat the wiring procedure for the left speaker to terminal L, making sure that you connect the red wire to "+" and black to "-". Note: – Speakers with an impedance of 4 Ohms or higher other than as supplied may be used instead. Speakers with a lower impedance, however, are unsuitable and will damage your set. – When headphones are inserted into the headphone jack the speakers are disconnected. GENERAL OPERATION 1. Press POWER to on position. – A source indicator lights up. 2. Select and press your source button CD, TUNER or TAPE. – The selected source indicator lights up. 3. Operate sound source according to the instructions of the respective chapter about the function. 4. Adjust the sound using the VOLUME 4 , 3 and DBB controls. – The volume level is briefly indicated in the display when you adjust it. 5. Press POWER again to switch off the set. – The selected source indicator goes out. SPEAKERS 4 + R – + L – AZ2755 CD RADIO CASSETTE RECORDE TUNER SHUFFLE POWER CD DBB 10 RADIO CD PLAYER RADIO RECEPTION 1. Press POWER to on position. 2. Press TUNER source button. – The TUNER indicator lights up. 3. Adjust BAND to select the desired FM/ AM waveband. 4. Tune to a radio station using the tuning knob. – For FM, pull out the telescopic antenna. Incline and turn the antenna. Reduce its length if the signal is too strong (very close to a transmitter). – For AM, the set is provided with a built-in antenna so the telescopic antenna is not needed. Direct the antenna by turning the whole set. 5. Adjust the sound using VOLUME 4 , 3 and DBB. 6. Press POWER again to switch off the set. – The TUNER indicator goes out. DISPLAY INDICATION FOR CD FUNCTIONS CD door open d1SC CD inserted – In stop mode total track number and total playback time – During CD playback elapsed playback time of current track and current track number – PAUSE elapsed playback time freezes and flashes when CD program active; also appears briefly when you store a track no SEL program activated but no tracks selected program cancelled/ PROG pressed for more than 2 seconds no d1SC no disc/error in CD operation or with the CD (see Troubleshooting) FULL program memory full – SHUFFLE/ REPEAT modes when the respective mode is activated English TUNER SHUFFLE REPEAT CD STOP SEARCH PLAY/PAUSE BAND TAPE PROG FM MHz 88 • 92 • 96 • 100 • 104 • 108 MHz FM B MW KHz 530 600 700 AZ2755 CD RADIO CASSETTE RECORDE TUNER SHUFFLE POWER CD DBB CD CD CD SHUFFLE CDREPEAT 11 CD PLAYER English PLAYING A CD 1. Press POWER to on position. 2. Press CD source button. – The CD indicator lights up. 3. To open the CD door, press OPEN on the CD door. 4. Insert a CD with the printed side facing up and press the CD door gently to close. 5. Press PLAY/PAUSE 2; on the set to start playback. 6. Adjust the sound using VOLUME 4 , 3 and DBB. 7. To interrupt playback press PLAY/PAUSE 2;. To resume, press PLAY/PAUSE 2; again. 8. To stop CD play, press STOP 9. 9. Press POWER again to switch off the set. – The CD indicator goes out. Note: CD playback will also stop when: – you press the CD door open; ...
Эта инструкция также подходит к моделям:CD-проигрыватели - AZ2755/17 (1.43 mb)