Оценок - 5, средний балл: 4
(
)
)
|
Фрагмент инструкции
• Before completly installing the unit, connect the wiring temporarily and make sure it is functioning properly. • Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. • Consult with your Metrik dealer if installation requires the drilling of holes or other modifications of the vehicle. • Install the unit securly and correctly to insure injure saftey of the driver and the passenger if there is a sudden stop, like an emergency stop. • If installation angle exceeds 30° from horizontal, the unit might not give its optimum performance and the CD may skip 30° • Avoid installing the unit where it would be subject to high temperature, such as in direct sunlight, in line of vents from the heater, or where it would be subject to dust, dirt or excessive vibration. DIN FRONT/REAR-MOUNT This unit can be properly installed either from "Front" (conventional DIN Front-mount) or "Rear" (DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods. DIN FRONT-MOUNT (Method A) Installation the unit 1 3 2 182 53 (Fig. 1) 1. Dashboard 2. Holder After inserting the sleve into the dashboard, select the appropriate tab according to the thickness of the dashboard material and bend them inwards to secure the sleve in place. 3. Rear Support Screw 2 1 2 6 5 4 3 7 (Fig. 2) Removing the unit 1. Dashboard 2. Nut (5mm) 3. Spring washer 4. Screw (5 x 25mm) 5. Screw 6. Strap Be sure to use the strap to secure the back of the unit in place. The strap can be bent by hand to the desired angle. 7. Plain washer 1. Frame 1 3 2. Insert fingers into the groove in the front of frame and pull out to remove the frame. (When re-attaching the frame, point the side with a groove downwards and attach it.) 3. Lever Insert the levers supplied with the unit into the grooves at both sides of the unit as shown in figure until they click. Pulling the levers makes it possible to remove the unit from the dashboard. DIN REAR-MOUNT (Method B) Installation using the screw holes on the sides of the unit. Fastening the unit to the factory radio1 mounting bracket. 1. Select a position where the screw holes of the bracket and the screw holes of the main unit become 3 5 2 2 5 aligned (are fitted), and tighten the screws at 2 places on each side. Use either truss screws (5 x 6mm) or 4 flush surface screws (4 x 6mm), depending on the shape of the screw holes in the bracket. 2. Screw 3. Factory radio mounting bracket 4. Dashboard or Console 5. Hook (Remove this part) Note: The mounting box, outer trim ring, and half-sleeve are not used for this method of installation. 3 HOW TO REMOVE AND INSTALL THE FRONT PANEL 1. Press the release button and pull-off the front panel. Place the front panel into the supplied case to protect it. 2. To install the front panel, insert the right side of thepanel into the housing first, then press the left side in until it locks in place. If the panel is not correctly installed some of the function keys or the display may not function properly. REMOVING THE FRONT PANEL Front Panel Release Button INSTALLING THE FRONT PANEL 4 WIRING CONNECTIONS 1. All connections should be soldered and insulated with electrical tape. 2. Be sure to connect the red power input lead to + 12V power terminal after all the other leads have been properly connected. 3. Run all ground wires to a common ground. 4. After all the connections are completed, press the “RESET” (26) button. ANTENNA RELAY WIRE A yellow wire has been provided for power antenna relays. The relay will automatically activate the antenna when the unit is turned on and retract when unit is turned off. CAUTION : Do not hook up the yellow wire directly to the antenna or damage may occur to the unit. WIRING CONNECTIONS FOR FOUR SPEAKERS SYSTEM ANTENNA CONNECTOR MEMORY BACK-UP IGNITION RED BLACK PINK CHOKE BOX MAIN UNIT (GREY) RCA CABLE Rch RED SWITCH (B+) GROUND (B–) Lch WHITE POWER YELLOW ANTENNA GREEN GREY + – + – FRONT Rch FRONT Lch SPEAKER SPEAKER GREEN/BLACK GREY/BLACK BLUE WHITE + – + – REAR Rch REAR Lch SPEAKER SPEAKER BLUE/BLACK WHITE/BLACK 5 Basic Operation + – 25 6 9 8 12 10 13 4 7 5 18 19 20 17 24 15 1 14 2 16 113 21 22 23 1.0 ON/OFF Press PWR button (1) to turn on. Press PWR again to turn it off. 2.0 Select Mode Press SEL button (2) to move display through volume, bass, treble, balance and fader functions. Use + (3) and – (4) buttons to adjust the selected mode. When mode has not been adjusted for 3 seconds, display returns to normal radio or CD display. VOL BAS TRE BAL FAD (Volume) Bass) (Treble) (Balance) (Fader) 3.0 Volume Adjust volume by pressing + (3) or – (4) button. 4.0 Bass 4.1 Press SEL button (2) two times. 4.2 Adjust Bass level using + (3) or – (4) button. 5.0 Treble 5.1 Press SEL button (2) three times. 5.2 Adjust Treble level using + (3) or – (4) button. 6.0 Balance 6.1 Press SEL button (2) four times. 6.2 A...