Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
• Never let the generator run in an inappropriately ventilated room! 2.5.7 Protections Engine Low oil pressure protection and high cooling water temperature protection. R5976956 B-10MOBILELED 19/06/2007 2.SystemOverview Image 2-15 Alternator Thermal-magnetic protection and earth leakage protection (with earth pin). Image 2-16 2.5.8 Maintenance Overview All maintenance points (air filter, oil drain pump, oil filler cap, oil filter, fuel filters, radiator filler cap) are easily accessible. For normal maintenance activities, check the engine manual. For engine or alternator failure, consult a local dealer. For a list of service center, see "Service and Maintenance of the Generator ", page 29. 2.5.9 Safety for the user Overview The standard versions of these generators are equipped with an earth leakage protection and a thermal-magnetic protection, following the IN-S electrical scheme. For connection of charges of class 1 (charges with earth) and charges of class 2 (charges with double insulation, to be recognized by the “double square” pictograph on the appliance) there are no restrictions concerning the number of charges connected at the same time. Respect the minimum square (mm.) and maximum length of the extension cables (to assure the correct switching off of the thermal-magnetic protection in case of short-circuit). 2.5.10 Spare parts generator Overview Nr Description Ordering reference Euro power Ordering reference Fleedguard Ordering reference Kubota 1 Oil filter D1105/V1505 398211105 LF 3776 1627132092 R5976956 B-10 MOBILE LED 19/06/2007 2.SystemOverview 2 Fuel filter D1105/V1505 398111105 FF 5226 1522143080 3 In line filter D1105/V1505 130000016 FF 149 128143012 4 Air filter cartridge1105/V1505 398011105 AF 4939 1574111083 5 V – belt D1105/V1505 A130 6 Gasket valve cover D1105 BG2/EBB A11105001 7 Battery 45Ah 12 V ( DIN 54577) 170000003 8 Injectors 16032-5300-0 9 Radiator assembly 10 Charging generator 11 AVR ( electronic ) 200990099 12 Anti vibration support ( A puffer motor ) 60/60 120000060 13 Anti vibration support ( A puffer motor ) 75/55 12000075 14 Anti vibration support RAEM350 RA350EM R5976956 B-10MOBILELED 19/06/2007 3.SetupoftheB-10MobileLED 3. SETUP OF THE B-10 MOBILE LED Overview • Installation of the B-10 Mobile LED • Powering the B-10 Mobile LED • Extending the LED display • Rotating the LED display • Move down the LED Display • Preparing for departure 3.1 Installation of the B-10 Mobile LED Useful tools In order to set up the B-10 Mobile LED more easily the following tools may be useful to purchase: • A level to verify the flat position of the trailer • A drill to position the 4 outriggers and fasten the 2 halves LED display parts together (4 bolts) How to install? 1. Place the trailer on a flat and hard ground. 2. Unhitch the trailer from the ball hitch. For this purpose, you may need to use the jockey wheel. After using the jockey wheel wind it fully up to its initial (up) position. Note: After using the jockey wheel wind it fully up to its initial (up) position. Caution: Only use the jockey wheel to engage and disengage the trailer on & from the towing hook. After usage, always wind the jockey wheel fully up to avoid damages on the jockey wheel. Image 3-1 3. Trigger the brake system of the B-10 Mobile LED (back position) 4. Take the wooden plate (in the B-10 Mobile LED left at door entrance) and position them below the outriggers. 5. Start by extending the front stabilizer. Tip: If the stabilizers cannot reach the wooden plates, put additional wooden plates under the outriggers. 6. Retract the jockey wheel completely. Caution: After using the jockey wheel wind it fully up to its initial (up) position. Only use the jockey wheel to engage and disengage the trailer on or from the towing hook. Caution: A jockey wheel may have a maximum allowed load of 250 kg. Do not use the jockey wheel faulty as it can damage the wheel and the folding system. 7. Extend the rear stabilizers. 8. Level the B-10 Mobile LED vehicle and try to position it as “flat” as possible in the length and the width. Use therefore a level and adjust the stabilizers accordingly. 3.2 Powering the B-10 Mobile LED How to power up? 1. Put the contact in the warm up position. After several seconds turn-on the generator with the contact key. R5976956 B-10 MOBILE LED 19/06/2007 3.SetupoftheB-10MobileLED Image 3-2 Contact key and power cable of pump 2. After several seconds turn-on the generator with this contact key. Caution: The generator of the B-10 Mobile LED needs to be well-ventilated. Therefore, the generator of the B-10 Mobile LED is not indented to run for a long period of time with the roof closed. Once the generator is running, the screen needs to be lifted immediately. 3. Insert the power cable of the hydraulic pump in the generator (Red-plug) 4. Connect the grounding conductor to a grounding rod or other acceptable earth grounding method. 3.3 Extending the LED display Extending process 1. Open the air arrival to sta...