Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Make any needed repairs or replacement before using on the reel, 4, UNPLUG ANY TOOLS OR APPLIANCES CONNECTED TO THE CORD REEL BEFORE REELING. 5, Always plug the Cord Reel into an approved, grounded 120 volt receptacle. (Even if you plan to use only Double Insulated tools or appliances.) 8, Check the cord periodically for damage and have damaged cords replaced immediately. 7, Keep your Cord Reel out of the reach of children. 8, Store your Cord Reel in a cool, dry place out of direct sunlight. Disconnect all tools or appliances before storage. 9, Do not expose the Cord Reel to grease or solvents. Clean with mild soap and water only. ■ 10. Have worn or broken parts replaced immediately. 11. DO NOT E1POSE CORD REEL TO WATER, RAIN OR SNOW OR USE IN DAMP AREAS. 12. Do not walk on or ride over extension cord or Cord Reel. 13. Keep cord away from oil, heat and sharp edges. 14. When using power tools or other appliances with the Cord Reel follow the safety rules listed in their Owner’s Manuals. 15. Carry only by the handle, never by the cord. 18. Turn tools or appliances off before plugging them in or unplugging them from the Cord Reel. 17. Use only 3 wire 18 AWG SJTW-A round outdoor extension cord. Maximum length 100 ft. GROUNDING: (GROUNDED CORD-CONNECTED TOOLS INTENDED FOR USE ON A SUPPLY CIRCUIT HAVING A NOWiNAL RATING LESS THAN 150 VOLTS) This tool is intended for use on a circuit that has an outlet that looks like the one illustrated in Sketch A. The tool has a grounding plug that looks like the plug illustrated in Sketch A. A temporary adapter, which looks like the adapter illustrated in Sketches B and C, may be used to connect this plug to a 2-pole receptacle as shown in Sketch B if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician. The grounding means, green-colored rigid ear, lug, etc. extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. C. GROUNDED OUTLET MX % / ® GROUNDING /TT\ PRONG IS VJLy LONGEST IF _ THE 3 PRONGS GROUNDED OUTLET BÜX ^ B. , ADAPTER . MEANS 84-011 OUTDOOR CORD REEL 84-012 OUTDOOR REEL & CORD NOTE: The Black & Decker Cord Reel is sold with or without a power cord. If you are installing your own power cord, perform all of the procedures in sections A through I. After you finish sections A through I, or if your cord reel comes assembled with a power cord, proceed to HOWTO USE YOUR CORD REEL on page 3, HOUSING IDENTIFY THE PARTS OF THE CORD REEL. (5) VERIFY YOUR CORD IS SAFE TO USE. 1, Only a 16-gauge, UL Underwriters Laboratories) listed, ROUND jacketed, 3-wire, outdoor extension cord in good condition is to be used, 2. Check the cord. Do not use cords with cracked insulation, splices, taped repairs, exposed wire or loose plug ends. WARNING; Cords with cracked insulation, splices, taped repairs, or exposed wire may be dangerous. You could receive an electrical shock. UPPER COVER WITH KNOB - LOWER COVER SEPARATOR <6)10-32x11/2 л $ MACHINE SCREWS (6)10-32 HARDWARE HEX NUTS © 1. Stretch your cord straight out. 2. Then double it in two long lengths. Touch the plug and socket together. Then work back to the center. 3. Mark the center of your cord with tape or some other marker. MARK CENTER WITH A PIECE OF TAPE PLUG (MALE) =DC& =^33 SOCKET (FEMALE) 1. Pass the plug (male) through-the large hole in the separator. 2. Pull the plug and cord until the center mark of the cord is in the center of the large hole in the separator. 3. Extend the cord out of the way in both directions as shown. 4. Push the cord into the channels, one on each side of the separator. 1 © 1. Place the lower cover on the side of the separator having the cord attached to the plug end. 2. Place the upper cover (with knob) on the side of the separator having the cord attached to the socket end. 3. Make sure the cord is still in the upper and lower separator channels (or the cord may be pinched). 4. Align the screw holes of the upper cover, separator, the lower cover. 5. Insert six screws through the holes in the upper cover, separator, and lower cover. Loosely assemble a nut onto each of the screws making sure that the nuts are inside the hex nut recesses. 6. Check that the cord is still in the channels of the separator and is not pinched between a cover and the separator. Then tighten the screws snuggly. SCREW UPPER COVER SEPARATOR *7* SOCKET END LOWER COVER © 1. Do not wind the cord onto the reel until the reel has been inserted into the housing. 2. Orient the housing handle and the reel as shown. 3. Pass the plug end of the cord through the hole in the housing, as shown (inside to outside). Pull nearly all of this half of the cord through the housing. 4. Pass the socket end of the cord through the other hole in the housing, as shown (inside to outside). Pull nearly all of this half of the ...
Эта инструкция также подходит к моделям:Осветительные приборы - 84-012 (2.53 mb)