Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
• Yellow LED Lighted and Red LED Flashing = Defective Battery Pack. IMPORTANT INFORMATION FOR RECHARGING HOT BA'n'ERIES Under extreme continuous use, the batteries in your battery pack will become hot. You should let a hot battery pack cool down for approximately 1 hour before attempting to recharge. When the battery pack becomes discharged and is hot, this will cause the red light on your battery charger to flash. When battery pack cools down, red light will glow continuously indicating fast charging mode, 1 hour charge time. Once the battery pack cools down, it will recharge battery pack in fast charging mode as normal. Note: This situation only occurs when extreme continuous use of your worklight causes the batteries to become hot. It does not occur under normal circumstances. Refer to "CHARGING BATTERY PACK" for normal recharging of batteries. If the charger does not charge your battery pack under normal circumstances, return both the battery pack and charger to your nearest Sears repair center for electrical check. ,_ WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. TO ATFACH BA'R'ERY PACK TO WORKLIGHT See Figure 2. Note: Battery pack is shipped in a lowcharge condition. Therefore, it must be charged prior to use. Refer to "CHARGING BA'I-rERY PACK" for charging instructions. • Align raised ribs on battery pack with grooves on bottom of worklight, then attach battery pack to workfight as shown in Figure 2. • Make sure latch on battery pack snaps into place and battery pack is secured to worklight before turning worklight on. _k CAUTION: When attaching battery pack to your worklight, be sure raised ribs and grooves align properly and latch snaps into place properly. Improper assembly can cause damage to worklight and battery pack. TO REMOVE BATTERY PACK FROM WORKLIGHT See Figure 3. • Depress latch located on front of battery pack (1) to release battery pack. • Pull forward on battery pack (2) to remove from worklight. DEPRESSLATCHTO RELEASEBATTERYPACK PULL TO REMOVE BATTERYPACK Fig. 3 RAISEDRIBS GROOVES LATCH BATTERYPACK Fig. 2 5 SWITCH See Figure 4. To turn your worklight on and off, depress switch trigger. MULTI-POSITION HEAD See Figure 4. Your worklight has the feature of a multi-position head that has positive stop clicks at each position. Rotate head to the desired position as shown in the arrows in Figure 4, MULTI-POSITION HEAD SWITCH TRIGGER Fig. 4 _1= WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. ,_ WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc. come in contact with plastic parts. They contain chemicals that can damage, weaken or destroy plastic. Do not abuse power tools. Abusive practices can damage tool as well as workpiece. ,_ WARNING: Do not attempt to modify this worklight or create accessories not recommended for use with this worklight. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury. BULB REPLACEMENT See Figure 5. When purchasing replacement bulb, request recommended part number 981258-001. TO REPLACE BULB: • Remove battery pack from worklight. • Remove the two screws securing lens cover, then remove cover. • Remove old bulb from spring. • Position new bulb in spring. • Replace lens cover and screws. • Replace battery pack. Note: For your convenience, a bulb storage area with extra bulb has been provided. It is located behind the lens cover. See Figure 5. SCREWS BULB EXTRA BULB BULB STORAGEAREA LENSCOVER FORMODELNO.315.268260 REQUESTBULBPARTNO.981258-001 Fig. 5 6 BAI-I'ERIES Your worklight's battery pack is equipped with nickel- cadmium rechargeable batteries. Length of service from each charging will depend on the type of work you are doing. The batteries in this worklight have been designed to provide maximum trouble free life. However, like all batteries, they wilt eventually wear out. Do not disassemble battery pack and attempt to replace the batteries. Handling of these batteries, especially when wearing rings and jewelry, could result in a serious burn. To obtain the longest possible battery life, we suggest the following: • Store and charge your batteries in a cool area. Temperatures above or below normal room temperature will shorten battery life. • Never store batteries in a discharged condition. Recharge them immediately after they are discharged. • All batteries gradually lose their charge. The higher the temperature the quicker they lose their charge. If you store your worklight for long periods of time without using it, recharge the batteries every month or two. This practice will prolong battery life. To preserve natural resources, please recycle or dispose of batteries properly. This product ...
Эта инструкция также подходит к моделям:Осветительные приборы - 26826 (727.62 kb)