Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
· Red Dot Finderscope · Accessory Tray · 2.5x Barlow · Hardware Packet—(3) Tripod Bolts with Wing Nuts, (3) Short Accessory Tray Bolts with Wing Nuts, (3) Tripod Leg Lock Screws TELESCOPE ASSEMBLY 1. Remove all components from the carton and identify all components. It is a good idea to lay all the parts out in front of you before assembly. READ THROUGH ASSEMBLY INSTRUCTION BEFORE YOU ASSEMBLE YOUR TELESCOPE. The only tool required in setting up your telescope is a slotted or Phillips blade screwdriver. Since your telescope is a precision optical system the parts require careful handling--particularly the telescope, eyepieces, and various accessory lenses. 2. Set-Up Tripod · Select one tripod leg. Loosen Tripod Leg Lock Screw (9) and extend the Tripod Leg Middle Section (6). For a moment, do not extend the leg fully...a shorter leg is less awkward to work with during set-up. Tighten the Tripod Leg lock Screw so that the Middle Section is securely in place. Repeat for the remaining two legs. 3. Attach Telescope and Finderscope · Note: Before assembling tripod legs to Easy Track® Mount, make sure the Accessory Tray Braces (7) face inward. Loosen long bolts at the top of Tripod Leg (5). Position the mount over the Tripod Leg as shown (fig. 2). and secure Easy Track® Mount to Tripod Leg. Repeat on the remaining two Tripod Legs. Once you have attached all Tripod Legs to the mount, securely tighten all wing nuts in place. · Locate the pre-assembled Telescope Main Tube (2). Remove Main Tube Locking Nuts (3) from screws extending from bottom of Telescope Main Tube (2). Insert extended screws into holes in cradle of Easy Track® Mounting System. Refasten Main Tube Locking Nuts (3). · Remove plastic insert on bottom side of finderscope to allow battery to make connection with battery contact for power. Turn power switch on. See finderscope page. · Look through main telescope tube at low power and establish a well-defined stationary target. Looking through red dot finderscope, alternate tightening each adjustment wheel (at rear and left side of finderscope) until the red dot of finderscope is precisely aligned and centered on the same object being viewed in main telescope tube. See finderscope page. Fig. 1 Fig. 2 4. Attach Accessory Tray Locate the Accessory Tray (8). Using the accessory tray bolts, wingnuts and washers connect the Accessory Tray to the Accessory Tray Braces (7). Start with one tripod leg and attach wingnuts. Wingnuts should be positioned beneath the accessory tray. Do not tighten wingnuts until all Accessory Tray Braces are attached as some adjustments may be required. 5. Attach Eyepiece Accessories Attach accessories as suggested in Intended Use Diagram. For example insert penta mirror assembly into focusing tube, then insert desired eyepiece into penta mirror assembly. 6. Remove Lens Cover from 60mm Objective Lens Your Bushnell Voyager Telescope is now ready to be used. To obtain the fullest enjoyment from your telescope, please refer to the additional information below. HOW TO USE YOUR NEW TELESCOPE Using the Penta Mirror Assembly: 1. A Basic Description: Bushnell is proud to present the Exclusive Penta Mirror Technology. This Penta Mirror Assembly provides the benefit of a convenient 90 degree viewing angle commonly associated with diagonal mirrors. However, the Penta Mirror provides something that diagonal mirrors cannot provide--right to left correct views of the any object viewed through the telescope. Unlike traditional diagonal mirrors that provide backward images of objects seen on land and in the night sky, the Penta Mirror allows correct images to be viewed. The groundbreaking benefit of this technology is that when viewing and locating objects through the telescope, when you want to move to the left, you move it to the left intuitively instead of fumbling around the sky becoming increasingly frustrated that you can’t move the telescope the way your intuition tells you that you need to move it. Fully Correct Image Reversed Image Upside-Down Image Upside-Down & Reversed Image Objects on land at great distances can be seen naturally (and readable) as if you were many times closer to the object. Objects in the sky appear as they appear in most star charts. For the first time ever, you will be able to see what you would expect resulting in excellent viewing satisfaction. In addition, the penta mirror has a special insert that is easily removed by backing out the eyepiece set screw and removing the insert to yield a 1.25” optical format receiver. 2. How-To-Use: Just like any traditional diagonal mirror, place the eyepieces directly into the rear of the Penta Mirror Assembly then place the Penta Mirror directly into the back of the telescope focusing tube, erecting lens or Barlow lens (See Intended Configuration Diagram). InsertPower Change Ring Zoom Eyepiece Penta Mirror Using the ZOOM Eyepiece Assembly: 1. Basic Description: In addition to our revolutionary Penta Mirror Technology, Bushnell is...