Оценок - 4, средний балл: 3 ( )

Производитель: Leupold Размер: 1022.43 kb Название файла: Язык инструкции:

NOTE: Settings may vary slightly per individual preferences, air temperature, and atmospheric conditions. NOTE: The side parallax adjustment knob is not to be used to focus the target image. If the reticle is first focused and the parallax then properly set, the image should be clear. EFR scopes and the adjustable objective Leupold EFR (Extended Focus Range) scopes can eliminate parallax for distances as short as 10 meters. Unlike conventional adjustable objective scopes, the focus ring on EFR models rotates more than 360°. It is important to pay special attention when adjusting these scopes. 1. Turn the focus ring counterclockwise (when viewing though the eyepiece) until it stops. 2. Turn the focus ring clockwise until the “10m” mark aligns with the indicator mark on the bell of the scope. 3. From this point, all readings of the focus ring are in numerical order when the ring is turned clockwise from the shooting position. 4. Adjust the ring as you would a standard adjustable objective model. installing a lens attachment Many Leupold scopes offer threaded objective and eyepiece rings to allow for the attachment of lens covers and a variety of Alumina® accessories. These attachments thread directly into the objective or eyepiece rings. Turn until finger tight – do not over tighten. To adjust the parallax distance, turn the focus ring. Using the Illuminated Reticle Using the Illuminated Reticle All Leupold Illuminated Reticle scopes may be used in either the standard or the illuminated state. When not illuminated, the reticle performs the same as the reticle in a standard Leupold scope. Illuminating the reticle allows a better distinction to be made in poorly lighted conditions between the target and the precise position of the aiming point. The control dial for the Leupold Illuminated Reticle is located above the eyepiece. To illuminate the reticle: 1. Grasp the illumination dial located at the top of the eyepiece shell. 2. Turn the dial clockwise from the OFF position to the first number indicated on the dial. 3. View the target through the scope to determine if the reticle is bright enough to stand out clearly against the target. 4. If more illumination is required, continue turning the dial clockwise until the reticle is clearly visible against the target. To preserve the life of the battery, always remember to turn the illumination dial to the OFF position when the scope is not in use. For prolonged storage, remove the battery. If the reticle fails to illuminate or appears dim even on the highest illumination setting, it is necessary to change the battery. WARNING: Always check to ensure that the firearm is unloaded before changing the battery in the scope. Changing the Battery Changing the Battery All Leupold Illuminated Reticle scopes use a 3-volt lithium photo battery. See page 36. To change the battery: 1. Remove the battery cover by grasping its edge (located around the top of the illumination dial) and twisting the cover counterclockwise while holding the sides of the illumination dial to keep the entire dial from turning. 2. Remove the old battery from its position in the center of the dial. Battery The battery for the Leupold Illuminated Reticle is located inside the control dial and can be changed without tools. This can be done in two ways: a. Grasp the edges of the battery between the thumb and forefinger and lift it free of the dial. OR b. Turn the scope so that the illumination dial faces downward and gently tap the eyepiece against the edge of your palm. 3. Insert the new battery, positive (+) side up. 4. Replace the battery cover on the illumination dial and turn it clockwise until it is secure while holding the sides of the illumination dial to keep the entire dial from turning. Replacement 3-volt lithium batteries: There may be other lithium batteries that are acceptable with your Leupold Illuminated Reticle scope. Check with your local retailer for other options. Duracell®. . . . . . . . . . .DL1/3N Eveready®. . . . . . . . . .2L76 Kodak®. . . . . . . . . . . .K58L Varta®. . . . . . . . . . . . .CR1/3N Sanyo® . . . . . . . . . . . .CR1/3N Leupold Means Minimal Maintenance Minimal Maintenance Lenses Leupold scope lenses are coated to reduce light reflections and light scattering, thus increasing light transmission through the scope. They should be cleaned as carefully as you would a camera lens. Begin by using a lens brush to remove dust and then pure alcohol, high-grade glass cleaner, or pure water on a cotton swab. Windage / elevation adjustments These adjustments are permanently lubricated. There is no need to lubricate them. Keep the adjustment covers on, except when adjusting, to keep out dust and dirt. (It’s worth noting that, unlike competitive brands, Leupold scopes are waterproof even without the caps in place.) Eyepiece adjustment This adjustment is permanently lubricated. There is no need to lubricate it. The eyepiece can be rotated as far as it will go in either direction. I...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: