Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
6.2. Loosen, but do not remove, the carburetor drain screw and drain fuel remaining in bowl into a small, clean container, then pour the fuel from the container into vehicle fuel tank. Tighten the carburetor drain screw. 6.3. Fill fuel tank to about 1 inch (2.5 cm) from top of fuel tank and, following manufacturer’s directions, add a commercially available fuel stabilizer (such as Sta-Bil®). 6.4. Disconnect fuel vent line from fuel tank vent nipple. 6.5. Plug the fuel tank vent nipple so that it is air tight. We recommend using a slip-on vinyl cap. Page 24 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual Storage 7. Disconnect the battery cables, negative (–) cable first. See WARNING “To avoid unintentionally starting...” in General Warnings on page 9. 8. Batteries should be clean and free of corrosion. Wash tops and terminals of batteries with a solution of baking soda and water (1 cup (237 mL) baking soda per 1 gallon (3.8 L) of water). Rinse solution off batteries. Do not allow this solution to enter the batteries. Be sure terminals are tight. Let the terminals dry and then coat them with Battery Terminal Protector Spray (P/N 603 00 00-03). 1231.FuelShut-offValve2.Closed(OFF) 3.Open(ON) NOTE:Whenselectingvalveposition,ensurethatitisfullyopenedorfullyclosed. Figure 14 Fuel Shut-off Valve 9. To protect the engine, remove spark plug and pour 1/2 ounce (14.2 mL) of SAE 10 weight oil into the engine through the spark plug hole. Rotate engine crankshaft by hand several times and then install the spark plug and tighten to 20 ft-lb (27 N·m). 10. Lower the passenger side seat and lower the cargo bed. 11. Adjust tires to recommended tire pressure. See Vehicle Specifications on page 40. 12. Perform semiannual periodic lubrication. See Periodic Lubrication Schedule on page 29. 13. Thoroughly clean front body, rear body, seats, cargo bed, engine compartment, and underside of vehicle. 14. Do not engage the park brake. Chock the wheels to prevent the vehicle from rolling. RETURNING THE STORED VEHICLE TO SERVICE 1. Make sure the key switch is in the OFF position and the Forward/Reverse handle is in the NEUTRAL position. Chock the wheels. 2. Raise the cargo bed to access the engine and battery. See WARNING “For vehicles with cargo beds...” in General Warnings on page 9. 3. Lift the front passenger seat. 4. Restore fuel system to operation (Figure 24). 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual Page 25 Maintenance 4.1. Remove plug from fuel tank vent. 4.2. Connect vent tube to fuel tank vent. 5. Connect battery cables, positive (+) cable first, and tighten terminals to 144 in-lb (16 N·m). Coat terminals with Battery Terminal Protector Spray (P/N 603 00 00-03). 6. Completely open the fuel shut-off valve (Figure 14). Make sure the valve is fully open. A partially closed fuel shut-off valve combined with the use of the choke can result in a fouled spark plug and engine failure. 7. Place the Forward/Reverse handle in the NEUTRAL position. Crank the engine until fuel is pumped into the carburetor and fuel lines and the engine starts. Turn the engine off. See following NOTE. NOTE: Due to the oil added to the engine in preparation for storage, engine may smoke excessively for a short time when it is run for the first time after storage. 8. Lower the passenger side seat and lower the cargo bed. 9. Adjust tires to recommended tire pressure. See Vehicle Specifications on page 40. 10. Perform the Pre-Operation and Daily Safety Checklist on page 17. MAINTENANCE See General Warnings on page 9. To ensure trouble-free vehicle performance, follow an established preventive maintenance program. Regular maintenance can prevent vehicle downtime and expensive repairs that result from neglect. Use the Pre-Operation and Daily Safety Checklist on page 17and the following Periodic Service Schedule and Periodic Lubrication Schedule to keep the vehicle in proper working condition. Any vehicle not functioning correctly should not be used until it is repaired. This will prevent further damage to the vehicle and avoid the possibility of injury due to unsafe conditions. Contact your local Husqvarna dealer for repairs, semiannual and annual periodic service. WARNING • Only trained technicians should service or repair the vehicle. Anyone doing even simple repairs orservice should have knowledge and experience in electrical and mechanical repair. The appropriateinstructions must be used when performing maintenance, service, or accessory installation. • If any problems are found during scheduled inspection or service, do not operate vehicle until repairsare made. Failure to make necessary repairs could result in fire, property damage, severe personalinjury, or death. • Do not wear loose clothing or jewelry, such as rings, watches, chains, etc., when servicing vehicle. • Turn the key switch to the OFF position, remove the key, place the Forward/Reverse handle in theNEUTRAL position, and chock the wheels prior to servicing the vehicle. • Moving parts: Do ...
Эта инструкция также подходит к моделям:Оборудование к ТС - HUV 4213-G (1.98 mb)