Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
Operating the machine with an improper oil level can damage engine components. Check the oil level with the engine off. 1 Check the oil dipstick. Gasoline/LPG Engine: located above the bellhousing on the bulkhead side of the engine. Diesel Engine: located on the engine block near the engine oil filter. Result: The oil level should be at the full mark on the dipstick. Add oil as needed. Ford LRG-425 EFI Engine Oil capacity (including filter) 4.5 quarts 4.3 liters Oil viscosity requirements below 60°F / 15.5°C 5W-30 -10° to 90°F / -23° to 32°C 5W-30 above -10°F / -23°C 5W-30 above 25°F / -4°C 10W-30 Use oils meeting API classification SH or SG grade. Units ship with 10-40 CC/SG. Genie S-80 & Genie S-85 PartNo.43650 Second Edition · Fifth Printing Operator's Manual Deutz F4L 1011F Engine Oil capacity (including filter) 8.5 quarts 8 liters Oil viscosity requirements below 60°F / 15.5°C (synthetic) 5W-30 -10°F to 90°F / -23°C to 32°C 10W-40 above -4°F / -34°C 15W-40 Engine oil should have properties of API classification CC/SE or CC/SF grades. Units ship with 10-40 CC/SG. Perkins 704-30 Engine Oil capacity (including filter) 9.6 quarts 9 liters Oil viscosity requirements below 60°F / 15.5°C 15W-40 -10°F to 90°F / -23°C to 32°C 10W-30 above -4°F / -34°C 15W-40 Engine oil should have properties of API classification CF4 grade. Units ship with 10-40 CC/SG. MAINTENANCE Check the Hydraulic Oil Level Maintaining the hydraulic oil at the proper level is essential to machine operation. Improper hydraulic oil levels can damage hydraulic components. Daily checks allow the inspector to identify changes in oil level that might indicate the presence of hydraulic system problems. 1 Be sure that the boom is in the stowed position, then visually inspect the sight gauge located on the side of the hydraulic oil tank. Add oil as needed. Result: The hydraulic oil level should be within the top 2 inches (5 cm) of the sight gauge. Hydraulic oil specifications Hydraulic oil type Dexron equivalent Tank capacity 45 gallons 170 liters Hydraulic system (including tank) 55 gallons 208 liters PartNo.43650 Genie S-80 & Genie S-85 Operator's Manual Second Edition· Fifth Printing MAINTENANCE Check the Engine Coolant Level - Liquid Cooled Models Maintaining the engine coolant at the proper level is essential to engine service life. Improper coolant level will affect the engine's cooling capability and damage engine components. Daily checks will allow the inspector to identify changes in coolant level that might indicate cooling system problems. Burn hazard. Beware of hot engine parts and coolant. Contact with hot engine parts and/or coolant may cause severe burns. 1 Check the fluid level in the coolant recovery tank. Add fluid as needed. Result: The fluid level should be at the FULL mark. Do not remove the radiator cap. Check the Batteries Proper battery condition is essential to good engine performance and operational safety. Improper fluid levels or damaged cables and connections can result in engine component damage and hazardous conditions. Electrocution hazard. Contact with hot or live circuits may result in death or serious injury. Remove all rings, watches and other jewelry. Bodily injury hazard. Batteries contain acid. Avoid spilling or contacting battery acid. Neutralize battery acid spills with baking soda and water. 1 Put on protective clothing and eye wear. 2 Be sure that the battery cable connections are free of corrosion. 3 Be sure that the battery hold downs and cable connections are tight. 4 Remove the battery vent caps. 5 Check the battery acid level. If needed, replenish with distilled water to the bottom of the battery fill tube. Do not overfill. 6 Install the vent caps. Adding terminal protectors and a corrosion preventative sealant will help eliminate corrosion on the battery terminals and cables. Genie S-80 & Genie S-85 PartNo.43650 Second Edition · Fifth Printing Operator's Manual Check the Tire Pressure This procedure does not need to be performed on machines equipped with the foam-filled tire option. Bodily injury hazard. An overinflated tire can explode and could cause death or serious injury. Tip-over hazard. Do not use temporary flat tire repair products. To safeguard maximum stability, achieve optimum machine handling and minimize tire wear, it is essential to maintain proper pressure in all air-filled tires. 1 Check each tire with an air pressure gauge. Add air as needed. Tire specifications Tire size 15-22.5SAT Pressure 100 psi 6.89 bar Scheduled Maintenance The scheduled maintenance items must be completed by a person trained and qualified to perform maintenance on this machine according to the procedures found in the service manual for this machine. Inspections and maintenance described below require the qualified entity to record and retain records of all inspections and maintenance items for four years. Machines that have been out of service for more than three months must receive the quarterly inspection befo...
Эта инструкция также подходит к моделям:Оборудование к ТС - 43650 (1.5 mb)
Оборудование к ТС - S-85 (1.5 mb)