Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
To turn hand vacuum ON ( I ), press up. To turn hand vacuum OFF ( 0 ), press down. 2. Cleaning with hard nozzle 1. Turn hand vacuum OFF. 2. Remove flexible rubber contour nozzle by pressing down on round nozzle release button. 3. Replace with hard nozzle by lining up the bottom of nozzle to the bottom of the dirt 3. container. Pivot upwards to snap into place. 4. Make sure the nozzle has snapped securely into place before using. 4 Power Cord with Cord Wrap System Exhaust ug110-4076_87R4E_1008.indd 4 12/10/08 3:31:19 PM 1.2. Operations Cleaning with flexible rubber contour nozzle Turn hand vacuum OFF. Remove hard nozzle by pressing down on round nozzle release button. 3. Replace with flexible rubber contour nozzle by lining up the bottom of nozzle to the bottom of the dirt container. Pivot upwards until it snaps into place. 4. Make sure the nozzle has snapped securely into place before using Emptying the dirt container Empty the dirt container after each use. A full dirt container may reduce suction or performance of vacuum. 1. Turn hand vacuum OFF. 2. Unplug hand vacuum from electrical outlet. 3. Press dirt container release latch down to disconnect dirt container and filter assembly from the unit. 4. Remove filter by grasping tabs on both sides of filter frame and pulling away from the dirt container. For best results, periodically tap filter assembly against trash can to remove dirt that has collected on the screen and filter. 5. Empty dirt into trash can. 6. Replace filter assembly by aligning side labeled “TOP” into top of dirt container. Grasp filter tabs and press firmly to ensure filter assembly is secure in dirt container. NOTE: Make sure side of filter assembly labeled "TOP" faces outward when inserting filter assembly into dirt container. 7. Reattach dirt container to unit by aligning bottom of dirt container to bottom of unit. Pivot upwards and snap into place. Use one hand to hold the unit and use the other hand to clip the dirt container securely in place. Maintenance and care Cleaning the filter and screen 1. Turn hand vacuum OFF. 2. Unplug hand vacuum from electrical outlet. 3. Disconnect dirt container and filter assembly from the unit. 4. Remove filter by grasping tabs on both sides of filter frame and pulling away from the dirt container. 3. 2. ATTENTION: For best performance, dirt container and filter assembly should becleaned after every use. 3. 4. 5. 6. 7. 5 4. ug110-4076_87R4E_1008.indd 5 12/10/08 3:31:19 PM Maintenance and care Cleaning the filter and screen continued 5. 5. Separate filter assembly by grasping tabs on both sides of assembly and pull. For best results, periodically tap filter and screen against trash can to remove dirt that has collected. 6. Reconnect filter and screen by aligning rectangular tab on filter with insert on screen. Press together to ensure assembly is secure. 6. 7. See page 5 to reattach dirt container. NOTE: The dirt container and screen may be rinsed with cold water. Ensure both are dry before reinserting. DO NOT RINSE PLEATED FILTER. Storage/Cord wrap system A wrap is attached to the cord for quick and easy storage. 1. To store the unit, turn hand vacuum OFF. Insert Tab 2. Unplug hand vacuum from electrical outlet. 3. Bundle cord, using wrap that is located on cord, to store. Nozzle Maintenance Keep nozzles clean and free of debris. 1. Wipe nozzles clean with damp cloth. Troubleshooting Hand vacuum won’t run Possible causes Remedies 1. Power cord not plugged in 1. Check electrical plug 2. Thermal protector is activated 2. Turn OFF and unplug the unit. Empty dirt container, clean filter and screen, and clear any clogs. Wait 30 minutes before turning the unit back on Hand Vacuum won’t pick up or low suction Possible causes Remedies 1. Dirt container not installed properly 1. Check assembly of dirt container making sure it is snapped in 2. Dirt container is full 2. Empty dirt container and reattach 3. Filter or screen is dirty 3. See instructions above. Replace filter if needed 4. Nozzles are clogged with debris 4. Wipe tools clean with damp cloth Other maintenance or service not included in the manual should be performed by an authorized service representative. 5a. Please do not return this product to the store. 6 ug110-4076_87R4E_1008.indd 6 12/10/08 3:31:19 PM BISSELL Consumer Services If your BISSELL product should require service: In the UK, Australia or New Zealand, call BISSELL Consumer Services at the numbers below and we will give you the location of a BISSELL Authorized Service Center in your area. For all other countries, contact your local in country distributor for questions, service, or repair. If you have questions about your warranty or need replacement parts please contact the numbers below. For UK inquiries: For Australian inquiries: Monday - Thursday 9 am — 5 pm Monday - Friday 9 am — 5 pm Friday 9 am — 4 pm BISSELL AUSTRALIA PTY LIMITED BISSELL Homecare (Overseas) Inc. Unit 35 The Boat Ya...