Оценок - 6, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Our mission is to ensure your pet’s safety by providing you the tools and techniques to successfully train your pet. If you have any questions, please contact the Customer Care Centre or visit our website at Table of Contents Prepare the Receiver Collar................................................................................ 3 Function and Response Table ............................................................................ 5 Fit the Receiver Collar ....................................................................................... 6 Terms of Use and Limitation of Liability .......................................................... 10 Caution .......................................................................................................... 11 Francais ........................................................................................................ 13 Nederlands .................................................................................................... 24 Espanol ......................................................................................................... 35 Deutsch ......................................................................................................... 46 Italiano .......................................................................................................... 57 3 Prepare the Receiver Collar Your Receiver Collar comes with short Contact Points installed. Use the long Contact Points for cats with long or thick hair. Tighten the Contact Points with pliers one-half turn beyond finger tight (A). Check the tightness weekly. To Insert and Remove the Batteries 1. With a coin, unlock the Battery Door and remove it (B). 2. Insert two 3-volt Lithium (CR2032 batteries) into the Battery Door (B). 3. Place the Battery Door back into the Receiver (C). 4. With a coin, slide Battery Door latch to lock it (C). Replacement batteries (3-volt, CR2032) can be found at many retailers. Contact the Customer Care Centre or visit our website at for a list of common retailers. 3 3 2 A-67 4 1 2 5 A B C T o set the Sta tic Cor rection Lev e l Read all the steps before attempting to set the Correction Level. 1. Place the magnet on the Correction Level Key Ring next to the Magnet Key Dot on the Receiver Collar. The Receiver Indicator Light will come on. 2. Remove the magnet from the Key Dot. The number of flashes indicates the Correction Level. 3. To increase the Correction Level, place the magnet next to the Magnet Key Dot within 5 seconds of performing the above step. The number of flashes indicates the new Correction Level. The Correction Levels increase in strength from 1 to 5. Activating the Magnet Key Dot while the Receiver Collar is on level 5 will cause the Receiver Collar to revert to level 1. Refer to the Function and Response Table below to choose the Correction Level that best fits your cat. The Receiver Collar is equipped to automatically increase the level of Static Correction the longer your cat remains in the Static Correction Zone if the collar is set at level 2 or above. The Receiver Indicator Light also acts as a low battery indicator, flashing every 4 to 5 seconds when battery replacement is required. (Bottom) (Top) Function and Response Table Indicator Light Response Correction Level Receiver Collar Function Temperament of cat 1 Flash 1 No Static Correction, Beep Only 2 Flashes 2 Low Static Correction Timid 3 Flashes 3 Medium Static Correction Timid or Average 4 Flashes 4 Medium-High Static Correction Average or High Energy 5 Flashes 5 High Static Correction High Energy Flashes once every 4 to 5 seconds Low Battery Note: Begin training with Correction Level 2 and only increase if your cat does not respond to the Static Correction. DD Fit the Receiver Collar Important: The proper fit and placement of your Receiver Collar is important for effective training. The Contact Points must have direct contact with your cat’s skin on the underside of his neck. To assure a proper fit, please follow these steps: 1. Make sure that the batteries are not installed in the Receiver Collar. 2. Start with your cat standing comfortably ( D). 3. Centre the Contact Points underneath your cat’s neck, touching the skin. If your cat has a long or thick coat, use the enclosed long Contact Points to reach through the hair. Note: It is sometimes necessary to trim the hair around the Contact Points to make sure that contact is consistent. 4. Check the tightness of the Receiver Collar by inserting one finger between the end of a Contact Point and your cat’s neck. The fit should be snug but not constricting ( E). 5. Allow your cat to wear the collar for several minutes then recheck the fit. Check the fit again as your cat becomes more comfortable with the Receiver Collar. 6. Trim the collar as follows ( F): a. Mark the desired length of the Receiver Collar wi...