Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Remove the two M2 x 3-mm screws that are located in the hard-drive bay door labeled "circle P." 6. Turn the computer over, and remove the three M2 x 3-mm screws that secure the palm rest to the bottom case. a. Remove the two M2 x 3-mm screws that are located on the back edge of the bottom case, underneath the display assembly. b. Remove the M2 x 3-mm screw located underneath the keyboard, on the right side of the bottom case, next to the microprocessor thermal cooling assembly. 7. Pull up on the pull tab that is attached to the palm-rest flex cable connector to remove it from the interface connector on the system board. Palm Rest Removal 1 M2 x 3-mm screws (3) 2 palm rest 3 palm-rest flex cable 4 bottom case 5 touch pad connector 6 back center of the palm rest NOTICE: Carefully separate the palm rest from the bottom case to avoid damage to the palm rest. 8. Starting at the back center of the palm rest, use your fingers to separate the palm rest from the bottom case by lifting up the inside of the palm rest while pushing in on the outside. Back to Contents Page Back to Contents Page Microprocessor Thermal Cooling Assembly Dell™ Latitude™ C610/C510 Service Manual Removing the Microprocessor Thermal Cooling Assembly Replacing the Microprocessor Thermal Cooling Assembly Removing the Microprocessor Thermal Cooling Assembly NOTICE: Disconnect the computer and any attached devices from electrical outlets, and remove any installed batteries. NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. NOTICE: Read "Preparing to Work Inside the Computer" before performing the following procedure. 1. Remove the hard drive. 2. Remove the keyboard. 3. Loosen the four captive screws that secure the microprocessor thermal cooling assembly to the system board. Microprocessor Thermal Cooling Assembly Removal 1 microprocessor thermal cooling assembly 2 captive screws (4) 3 right side 4. Lift the microprocessor thermal cooling assembly up and out of the system board. Replacing the Microprocessor Thermal Cooling Assembly 1. Place the right side of the microprocessor thermal cooling assembly under the palm rest and lower the assembly onto the system board. 2. Tighten the four captive screws, labeled 1 through 4, in consecutive order. Back to Contents Page Back to Contents Page Microprocessor Module Dell™ Latitude™ C610/C510 Service Manual Removing the Microprocessor Module Replacing the Microprocessor Module Removing the Microprocessor Module NOTICE: Disconnect the computer and any attached devices from electrical outlets, and remove any installed batteries. NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. NOTICE: Read "Preparing to Work Inside the Computer" before performing the following procedure. Microprocessor Module Removal NOTICE: Do not touch the processor die. Press and hold the microprocessor down on the substrate on which the die is mounted while turning the cam screw to prevent intermittent contact between the cam screw and microprocessor. NOTICE: To avoid damage to the microprocessor, hold the screwdriver so that it is perpendicular to the microprocessor when turning the cam screw. 1 screwdriver (perpendicular to microprocessor) 2 pin-1 corner 3 processor die (do not touch) 4 ZIF socket 5 ZIF-socket cam screw 1. Remove the hard drive. 2. Remove the keyboard. NOTICE: To ensure maximum cooling for the microprocessor, do not touch the heat transfer areas on the microprocessor thermal cooling assembly. The oils in your skin reduce the heat transfer capability of the thermal pads. 3. Remove the microprocessor thermal cooling assembly. NOTICE: When removing the microprocessor module, pull the module straight up. Be careful not to bend the pins on the microprocessor module. 4. To loosen the ZIF socket, use a small, flat-blade screwdriver and rotate the ZIF-socket cam screw counter-clockwise until it comes to the cam stop. The ZIF-socket cam screw secures the microprocessor to the system board. Take note of the arrow on the ZIF-socket cam screw (see "Microprocessor Module Removal"). 5. Use a microprocessor extraction tool to remove the microprocessor module. Replacing the Microprocessor Module NOTICE: Ensure that the cam lock is in the fully open position before seating the microprocessor module. Seating the microprocessor module properly in the ZIF socket does not require force. NOTICE: A microprocessor module that is not properly seated can result in an intermittent connection, or permanent damage to the microprocessor and ZIF socket. 1. Align the pin-1 corner of the microprocessor module with the pin-1 corner of the ZIF socket, and insert the microprocessor module. NOTE: The pin-1 corner of the microprocessor module has a triangle that aligns with the triangle on the pin-1 corner of the ZIF socket. NOTICE: You must position the microprocessor module correctly in the ZIF s...