Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
1. Follow the procedures in Working on Your Computer. 2. Turn your computer upside down. 3. If your computer has a security screw for the modular drive, remove the security screw. 4. Push the release latch in to release it. 5. Use the release latch to slide the drive out of the modular bay. 6. Remove the M2.5 x 5-mm screw that holds the release latch in place. 7. Slide the release latch out from the release latch carrier. 8. Remove the M2.5 x 5-mm screw that holds the carrier for the release latch in place. 9. Slide the release latch carrier out of the hard drive carrier. NOTICE: To prevent data loss, turn off your computer before removing the hard drive. Do not remove the hard drive while the computer is on or in Sleep state. NOTICE: Hard drives are extremely fragile. Exercise care when handling the hard drive. 1 security screw 2 modular bay 3 modular drive 4 release latch 1 release latch 2 release latch carrier 3 M2.5 x 5-mm screw 10. Remove the three M2.5 x 5-mm screws on the cover of the hard drive carrier. 11. Lift the cover up at an angle and remove. 12. Remove the four M2.5 x 5 screws from the hard drive bracket. 13. Lift the hard drive up at an angle and disconnect it from the hard drive carrier. 1 M2.5 x 5-mm screw 2 release latch carrier 3 hard drive carrier 1 cover 2 M2.5 x 5-mm screws (3) 3 hard drive carrier 1 hard drive carrier 2 M2.5 x 5-mm screws (4) 3 hard drive 4 hard drive bracket 14. Lift the connector-end of the hard drive and remove the hard drive from the hard drive bracket. 15. Pull out on the sides of the blue bumper to remove it from the hard drive. Replacing the Modular Hard Drive 1. With the top of the bumper facing up, place the end of the blue bumper on the end of the hard drive opposite from the connector, then enclose the two sides of the hard drive with the blue bumper. 1 hard drive 2 hard drive carrier 1 hard drive 2 connector 3 hard drive bracket 1 hard drive 2 blue bumper CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. NOTICE: Hard drives are extremely fragile. Exercise care when handling the hard drive. NOTICE: Use firm and even pressure to slide the hard drive into place. Excessive force may result in damage to the connector. NOTICE: The top and bottom of the blue bumper are different. The top has protruding ridges, and the bottom is flatter with slight ridges. When replacing the blue bumper around the hard drive, ensure that the top is installed facing up. 2. Place the end that is opposite from the connector on the hard drive into the hard drive bracket, ensuring that the hard drive fits into each corner of the hard drive bracket. 3. Lower the hard drive into the hard drive bracket. 4. Place the hard drive into the carrier at an angle. 5. Connect the hard drive to the connector in the carrier and lower the hard drive into the carrier. 6. Replace the four M2.5 x 5-mm screws in the hard drive bracket. 1 hard drive 2 blue bumper 3 connector 4 top of blue bumper 1 hard drive 2 connector 3 hard drive bracket 4 corner of hard drive bracket (2) 1 hard drive 2 hard drive carrier 3 connector 7. Attach the side of the cover where it is angled, ensuring the tabs on the cover fit properly into the notches on the carrier. 8. Set the cover in place and replace the three M2.5 x 5-mm screws. 9. Slide the release latch carrier into the hard drive carrier. 10. Replace the M2.5 x 5-mm screw that holds the carrier for the release latch in place. 11. Slide the release latch into the hard drive carrier. 12. Replace the M2.5 x 5-mm screw that holds the release latch in place. 1 hard drive carrier 2 M2.5 x 5-mm screws (4) 3 hard drive 4 hard drive bracket 1 notches in hard drive carrier 2 tabs on carrier cover 3 M2.5 x 5-mm screws (3) 1 M2.5 x 5-mm screw 2 release latch carrier 3 hard drive carrier 13. Slide the hard drive carrier into the modular bay. 14. Push the release latch in to hold the carrier in place. 15. If your computer has a security screw for the modular drive, replace the security screw. 16. Follow the procedures in After Working on Your Computer. 17. Install the operating system, drivers, and utilities for your computer, as needed. For more information, see the Setup and Quick Reference Guide that shipped with your computer at support.dell.com. Back to Contents Page 1 release latch 2 hard drive carrier 3 M2.5 x 5-mm screw 1 hard drive carrier 2 release latch Back to Contents Page Hinge Covers Dell™ Latitude™ E6400 and E6400 ATG and Mobile Workstation Precision™ M2400 Service Manual Removing the Hinge Covers Replacing the Hinge Covers Removing the Hinge Covers The hinge covers are not interchangeable; the left one covers the DisplayPort connector and the right one covers the RJ-45 network connector. 1. Follow the procedures in Before Working on Your Computer. 2. Remove the bottom of the base assembly (see Removing the Bottom of the Base Assembly). 3. Remove the M2.5 x 5-mm screw from each hinge cov...